manualshive.com logo in svg

evertz 7847FSEDA Series, Руководство пользователя

Поделиться
Скачать
evertz 7847FSEDA Series Скачать руководство пользователя страница 67

7847FSEDA Series  

Frame Synchronizer and Distribution Amplifier 

 

 

Revision 0.1

 

Page - 57

 

Loudness Range Low: 

This field displays the lowest calculated loudness value within the duration of 

the 

Integrated Loudness

 calculation, given the exclusions and thresholds used as described above in 

the calculation of the 

Loudness Range

. This control is used for monitoring purposes only.  The value 

is reported in LUFS 

 

Loudness Range High: 

This field displays the highest calculated loudness value within the duration 

of the 

Integrated Loudness

 calculation, given the exclusions and thresholds used as described above 

in the calculation of the 

Loudness Range

. This control is used for monitoring purposes only.  The 

value is reported in LUFS 
 

Reset: 

This control allows the user to flush the buffer for the 

Integrated Loudness 

calculation. This 

control should be activated each time a new 

Integrated Loudness 

value is to be obtained. 

 

Start/Continue: 

This control allows the user to commence or resume the duration in which loudness 

values are being used to calculate the 

Integrated Loudness 

measurement. 

 

Stop/Pause: 

This control allows the user to terminate or pause the duration in which loudness values 

are being used to calculate the 

Integrated Loudness 

measurement. Each time this button is activated, 

a new 

Integrated Loudness 

value will be produced. 

 

5.2.14.4. IntelliGain

®

 Traps [+IG2] 

The IntelliGain

® 

audio loudness processing module can provide confidence monitoring with SNMP trap 

alarm notification.  These alarms can be enabled and disabled on an individual audio program basis 
using the IntelliGain

 Traps tab. 

 
The IntelliGain Traps tab contains the IntelliGain

®

 program trap enables, as well as corresponding trap 

status for each IntelliGain

®

  audio program. Figure  5-24  illustrates the layout of these controls in the 

VistaLINK® PRO configuration view. 
 
To enable or disable an SNMP alarm notification, either check or un-check the defined control. 
 
The IntelliGain

®

  audio loudness processing module also provides trap status information on the 

IntelliGain traps tab.  If a trap is sent by the IntelliGain

®

 system, the trap status box will change state 

indicating the current value for that trap.  For example, if the trap status box is the colour green, then 
the trap has not been sent, and the trap is not in the alarm state. However, if the status box is the colour 
red, then the fault is in a current state of alarm.  Once corrected, the status box will turn back to the 
colour green. 
 

Содержание 7847FSEDA Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды