Epson S1C33L26 Скачать руководство пользователя страница 427 | Manualshive

Страница: 427 / 722

background image

25 A/D CONVERTER (ADC10)

S1C33L26 TECHNICAL MANUAL

Seiko Epson Corporation

25-9

A/D Conversion Result Register (ADC10_ADD)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

A/D Conversion
Result Register
(ADC10_ADD)

0x301300

(16 bits)

D15–0 ADD[15:0] A/D converted data

ADD[9:0] are effective when
STMD = 0 (ADD[15:10] = 0)
ADD[15:6] are effective when
STMD = 1 (ADD[5:0] = 0)

0x0 to 0x3ff

0x0

R

D[15:0] ADD[15:0]: A/D Converted Data Bits

The A/D conversion results are stored. (Default: 0x0)

The data alignment in this 16-bit register (conversion result storing mode) can be selected using the
STMD/ADC10_TRG register.

ADD bit

15

...

10

9

...

6

5

...

0

Left justify mode (STMD = 1) (MSB)

10-bit conversion results

(LSB)

0

...

0

Right justify mode (STMD = 0)

0

...

0

(MSB)

10-bit conversion results

(LSB)

6.1 Conversion Data Alignment

Figure 25.

This register is a read-only, so writing to this register is ignored.

A/D Trigger/Channel Select Register (ADC10_TRG)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

A/D Trigger/
Channel Select
Register
(ADC10_TRG)

0x301302

(16 bits)

D15–14 –

reserved

–

–

–

0 when being read.

D13–11 ADCE[2:0] End channel select

0x0 to 0x5

0x0 R/W

D10–8 ADCS[2:0] Start channel select

0x0 to 0x5

0x0 R/W

D7

STMD

Conversion result storing mode

1 ADD[15:6]

0 ADD[9:0]

0

R/W

D6

ADMS

Conversion mode select

1 Continuous 0 Single

0

R/W

D5–4 ADTS[1:0] Conversion trigger select

ADTS[1:0]

Trigger

0x0 R/W

0x3
0x2
0x1
0x0

#ADTRIG pin

reserved

T8 Ch.2

Software

D3

–

reserved

–

–

–

0 when being read.

D2–0 ADST[2:0] Sampling time setting

ADST[2:0]

Sampling time 0x7 R/W Always set to 0x7.

0x7
0x6
0x5
0x4
0x3
0x2
0x1
0x0

9•ADCCLK
8•ADCCLK
7•ADCCLK
6•ADCCLK
5•ADCCLK
4•ADCCLK
3•ADCCLK
2•ADCCLK

D[15:14] Reserved

D[13:11] ADCE[2:0]: End Channel Select Bits

Sets the conversion end channel with a channel number from 0 to 5. (Default: 0x0 = AIN0)

Analog inputs can be A/D-converted continuously from the channel set by ADCS[2:0] to the channel set
by ADCE[2:0] in one A/D conversion. If only one channel is to be A/D converted, set the same channel
number in both ADCS[2:0] and ADCE[2:0].

6.2 Relationship between ADCS/ADCE and Input Channels

Table 25.

ADCS[2:0]/ADCE[2:0]

Channel selected

0x7–0x6

Reserved

0x5

AIN5

0x4

AIN4

0x3

AIN3

0x2

AIN2

0x1

AIN1

0x0

AIN0

(Default: 0x0)

D[10:8] ADCS[2:0]: Start Channel Select Bits

Sets the conversion start channel with a channel number from 0 to 5. (Default: 0x0 = AIN0)

D7

STMD: Conversion Result Storing Mode Bit

Selects the data alignment when the conversion results are loaded into ADD[15:0].

«
...
425
426
427
428
429
...
»

Содержание S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C33L26

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: Omega Страницы: 56

Бренд: Omega Страницы: 2

Бренд: D+H Страницы: 32

Бренд: Frico Страницы: 8

Бренд: Grosvenor Страницы: 5

Бренд: D+H Страницы: 16

Бренд: CompuPro Страницы: 33

Бренд: 4IPNET Страницы: 11

Бренд: Taylor Страницы: 34

Dynamic Boiler Controller

Бренд: Intiel Страницы: 25

Бренд: Watt Stopper Страницы: 3

Бренд: ZKTeco Страницы: 13

Бренд: TAC Страницы: 4

Бренд: Infineon Technologies Страницы: 2150

Бренд: Omron Страницы: 25

Бренд: Eaton Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды