Epson S1C33L26 Скачать руководство пользователя страница 371 | Manualshive

Страница: 371 / 722

background image

22 REMOTE CONTROLLER (REMC)

22-6

Seiko Epson Corporation

S1C33L26 TECHNICAL MANUAL

To use this interrupt, set REMFIE/REMC_INT register to 1. If REMFIE is set to 0 (default), the interrupt re-
quest attributable to this cause will not be sent to the ITC.

When REMFIF is set to 1, REMC outputs an interrupt request to the ITC. An interrupt will be generated if the
ITC and C33 PE Core interrupt conditions are met.

REMFIF should be inspected in the REMC interrupt handler routine to determine whether the REMC interrupt
is attributable to input signal falling edge.

The interrupt cause should be cleared in the interrupt handler routine by resetting (writing 1 to) REMFIF.

For more information on interrupt processing, see the “Interrupt Controller (ITC)” chapter.

Control Register Details

22.7

7.1 List of REMC Registers

Table 22.

Address

Register name

Function

0x301500

REMC_CFG

REMC Configuration Register

Controls the clock and data transfer.

0x301502

REMC_CAR

REMC Carrier Length Setup Register

Sets the carrier H/L section lengths.

0x301504

REMC_LCNT REMC Length Counter Register

Sets the transmit/receive data length.

0x301506

REMC_INT

REMC Interrupt Control Register

Controls interrupts.

The REMC registers are described in detail below. These are 16-bit registers.

Note: When data is written to the registers, the “Reserved” bits must always be written as 0 and not 1.

REMC Configuration Register

(REMC_CFG)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

REMC
Configuration
Register
(REMC_CFG)

0x301500

(16 bits)

D15–12 CGCLK[3:0] Carrier generator clock division

ratio select
(Prescaler output clock)

CGCLK[3:0]

LCCLK[3:0]

Division ratio

0x0 R/W Source clock =

PCLK2

0xf

0xe
0xd
0xc
0xb
0xa
0x9
0x8
0x7
0x6
0x5
0x4
0x3
0x2
0x1
0x0

reserved

1/16384

1/8192
1/4096
1/2048
1/1024

1/512
1/256
1/128

1/64
1/32
1/16

1/8
1/4
1/2
1/1

D11–8 LCCLK[3:0] Length counter clock division ratio

select
(Prescaler output clock)

0x0 R/W

D7–2 –

reserved

–

–

–

0 when being read.

D1

REMMD

REMC mode select

1 Receive

0 Transmit

0

R/W

D0

REMEN

REMC enable

1 Enable

0 Disable

0

R/W

D[15:12] CGCLK[3:0]: Carrier Generator Clock Division Ratio Select Bits

Selects a carrier generation clock from the 15 prescaler (PSC Ch.1) output clocks (PCLK2 division ra-
tio).

7.2 Carrier Generation Clock (PCLK2 Division Ratio) Selection

Table 22.

CGCLK[3:0]

Division ratio

CGCLK[3:0]

Division ratio

0xf

Reserved

0x7

1/128

0xe

1/16384

0x6

1/64

0xd

1/8192

0x5

1/32

0xc

1/4096

0x4

1/16

0xb

1/2048

0x3

1/8

0xa

1/1024

0x2

1/4

0x9

1/512

0x1

1/2

0x8

1/256

0x0

1/1

(Default: 0x0)

D[11:8] LCCLK[3:0]: Length Counter Clock Division Ratio Select Bits

Selects a data length counter clock from the 15 prescaler (PSC Ch.1) output clocks (PCLK2 division ra-
tio).

«
...
369
370
371
372
373
...
»

Содержание S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C33L26

Бренд: BEIER-Electronic Страницы: 22

Бренд: Jedia Страницы: 12

Бренд: JED Micro Страницы: 10

Бренд: JCM Technologies Страницы: 2

FSDrive-MV1000 Series

Бренд: YASKAWA Страницы: 260

Бренд: YASKAWA Страницы: 114

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 152

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 2

Бренд: YASKAWA Страницы: 58

Бренд: Matelec Страницы: 16

Optidrive Elevator

Бренд: Invertek Страницы: 5

Бренд: Techtrol Страницы: 4

Бренд: Allen-Bradley Страницы: 162

Driver LED 1x2A/48V

Бренд: PXM Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды