manualshive.com logo in svg

Epson Buzzer S1C31D51, Техническое руководство

Техническое описание Epson Buzzer S1C31D51 доступно для бесплатного скачивания на нашем сайте. Этот генератор импульсов подходит для широкого спектра приложений и оснащен подробным техническим руководством. Скачайте его с нашего веб-сайта для полного понимания функций и возможностей этого продукта.

Поделиться
Скачать
background image

2  POWER SUPPLY, RESET, AND CLOCKS

S1C31D50/D51 TECHNICAL MANUAL

 

Seiko Epson Corporation 

2-9

(Rev. 2.00)

2.3.4  Operations

Oscillation start time and oscillation stabilization waiting time

 

The oscillation start time refers to the time after the oscillator circuit is enabled until the oscillation signal is ac-
tually sent to the internal circuits. The oscillation stabilization waiting time refers to the time it takes the clock 
to stabilize after the oscillation starts. To avoid malfunctions of the internal circuits due to an unstable clock 
during this period, the oscillator circuit includes an oscillation stabilization waiting circuit that can disable sup-
plying the clock to the system until the designated time has elapsed. Figure 2.3.4.1 shows the relationship be-
tween the oscillation start time and the oscillation stabilization waiting time.

Oscillator circuit enable

(

∗

OSC

∗

EN)

Oscillation waveform

Digitized oscillation waveform

Oscillator circuit output clock

(

∗

OSC

∗

CLK)

Oscillation stabilization waiting completion flag

(

∗

OSC

∗

STAIF)

    System supply waiting time

Oscillation start time

Oscillation stabilization waiting time

Figure 2.3.4.1  Oscillation Start Time and Oscillation Stabilization Waiting Time

 

The oscillation stabilization waiting times for the OSC1 and OSC3 oscillator circuits can be set using the 
CLGOSC1.OSC1WT[1:0] bits and CLGOSC3.OSC3WT[2:0] bits, respectively. To check whether the oscilla-
tion stabilization waiting time is set properly and the clock is stabilized immediately after the oscillation starts 
or not, monitor the oscillation clock using the FOUT output function. The oscillation stabilization waiting time 
for the IOSC oscillator circuit is fixed at 16 IOSCCLK clocks. The oscillation stabilization waiting time for the 
OSC1 oscillator circuit should be set to 16,384 OSC1CLK clocks or more when crystal oscillator is selected, or 
4,096 OSC1CLK clocks or more when internal oscillator is selected. The oscillation stabilization waiting time 
for the OSC3 oscillator circuit should be set to 1,024 OSC3CLK clocks or more.

 

When the oscillation stabilization waiting operation has completed, the oscillator circuit sets the oscillation sta-
bilization waiting completion flag and starts clock supply to the internal circuits.

Note:  The oscillation stabilization waiting time is always expended at start of oscillation even if the os-

cillation stabilization waiting completion flag has not be cleared to 0.

 

When the oscillation startup control circuit in the OSC1 oscillator circuit is enabled by setting the CLGOSC1.OS-
C1BUP bit to 1, it uses the high-gain oscillation inverter for a set period of time (startup boosting operation) after 
the oscillator circuit is enabled (by setting the CLGOSC.OSC1EN bit to 1) to reduce oscillation start time. Note, 
however, that the oscillation operation may become unstable if there is a large gain differential between normal 
operation and startup boosting operation. Furthermore, the oscillation start time being actually reduced depends 
on the characteristics of the resonator used. Figure 2.3.4.2 shows an operation example when the oscillation start-
up control circuit is used.

(1) CLGOSC1.OSC1BUP bit = 0 (startup boosting operation disabled)

Normal operation

INV1N[1:0] setting gain

Oscillator circuit enable

(CLGOSC.OSC1EN)

Oscillation inverter

Oscillation waveform

Содержание Buzzer S1C31D51










































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Buzzer S1C31D51

Gardena EasyPlus Operator'S Manual preview
EasyPlus
Бренд: Gardena Страницы: 14
Gardena 1273 Operating Instructions preview
1273
Бренд: Gardena Страницы: 4
Gantner GAT ACCESS 6100 User Manual preview
GAT ACCESS 6100
Бренд: Gantner Страницы: 4
Rachio IRO Installation Manual preview
IRO
Бренд: Rachio Страницы: 2
L. G. B. 51099 Instructions preview
51099
Бренд: L. G. B. Страницы: 2
L-Acoustics LA4X Product Information preview
LA4X
Бренд: L-Acoustics Страницы: 36
nekos SKY 650 Manual For Installation And User Manual preview
SKY 650
Бренд: nekos Страницы: 8
nekos SKY 450 Installation And Use Manual preview
SKY 450
Бренд: nekos Страницы: 8
ccei MPZ Technical Instructions preview
MPZ
Бренд: ccei Страницы: 16
Zonex DIGI3U Installation Manual preview
DIGI3U
Бренд: Zonex Страницы: 16
Velleman CHLSC2 User Manual preview
CHLSC2
Бренд: Velleman Страницы: 22
National Instruments NI 9683 User Manual And Specifications preview
NI 9683
Бренд: National Instruments Страницы: 27
DH Instruments MPC1-1000 User Manual preview
MPC1-1000
Бренд: DH Instruments Страницы: 30
Maverick EP7312 User Manual preview
EP7312
Бренд: Maverick Страницы: 122
Pro-face LT-4201TM Installation Manual preview
LT-4201TM
Бренд: Pro-face Страницы: 48
Eaton Jockey XTJP O & M Manual preview
Jockey XTJP
Бренд: Eaton Страницы: 12
Omron R88D-GT series User Manual preview
R88D-GT series
Бренд: Omron Страницы: 510
Inkbird ITC-1000F User Manual preview
ITC-1000F
Бренд: Inkbird Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды