manualshive.com logo in svg

Epson Buzzer S1C31D51, Техническое руководство

Техническое описание Epson Buzzer S1C31D51 доступно для бесплатного скачивания на нашем сайте. Этот генератор импульсов подходит для широкого спектра приложений и оснащен подробным техническим руководством. Скачайте его с нашего веб-сайта для полного понимания функций и возможностей этого продукта.

Поделиться
Скачать
background image

21  HW Processor (HWP) and Sound Output

S1C31D50/D51 TECHNICAL MANUAL

 

Seiko Epson Corporation 

21-17

(Rev. 2.00)

Terminating memory check

 

The following shows the procedure to terminate the memory check being executed.
1.  Confirm that the STATE.STATE[15:0] bits = 0x0002 to 0x0005 (during memory check).
2.  Confirm that the STATUS.READY bit = 1. 

(Command acceptable)

3.  Set the COMMAND.COMMAND[7:0] bits to 0xff. 

(Select Memory Check Stop command)

4.  Write 1 to the HWPCMDTRG.HWP0TRG bit. 

(Trigger to issue command)

5.  Wait until the HWPINTF.HWP0IF bit is set to 1 (interrupt). 

(Occurrence of state transition)

6.  Confirm that the STATE.STATE[15:0] bits = 0x0001 (mc_state_idle).
7.  Write 0 to the HWPINTF.HWP0IF bit. 

(Clear interrupt flag)

Memory check error

 

When an error occurs during processing of the memory check function, the HWPINTF.HWP1IF bit is set to 1 (an 
interrupt can be generated). The error contents can be confirmed by reading the ERROR.ERROR[15:0] bits. As 
shown in Table 21.4.2.2, the ERROR.ERROR

x

 bit corresponding to the error that has occurred is set to 1.

Table 21.4.2.2  List of Memory Check Errors

ERROR.ERROR[15:0] bits

Error

Meaning

0000 0000 0000 0000

error_no_error

No error has occurred.

Non-fatal error

xxxx xxxx xxxx xxx1 (bit 0) error_command

A command that is undefined or is ineffective in the cur-

rent state has been specified.

Fatal error

x1xx xxxx xxxx xxxx (bit 14) error_function_id

An undefined function ID has been specified.

1xxx xxxx xxxx xxxx (bit 15) error_others

Another error has occurred.

 

When a non-fatal error has occurred, reissue a valid command. 

 

When a fatal error has occurred, remove the cause of error and redo the processing from initialization.

21.5  Interrupts

The HWP has a function to generate the interrupts shown in Table 21.5.1.

Table 21.5.1  HWP Interrupt Function

Interrupt

Interrupt flag

Set condition

Clear condition

Error occurrence HWPINTF.HWP1IF When a sound play error (see Table 21.4.1.2) or a memory 

check error (see Table 21.4.2.2) has occurred

Writing 0.

State transition HWPINTF.HWP0IF When a state transition of which the interrupt has not been 

masked occurs

Writing 0.

Interrupt enable

 

To enable HWP interrupts, the HWPINTE.HWPIE bit must be set to 1. An interrupt request is sent to the CPU 
core only when the interrupt flag is set in this status. For more information on interrupt control, refer to the “In-
terrupt” chapter.

State transition interrupt mask

 

The HWP provides a HWP internal register that contains the interrupt mask bits used for setting whether to set 
the HWPINTF.HWP0IF bit (to generate an interrupt) or not when a state transition occurs. By setting the inter-
rupt mask bits to 1, an interrupt can be generated when the corresponding state transition occurs.

Table 21.5.2  State Transition Interrupt Mask Bits

Function

Interrupt mask bit

State transition

Sound play

INTMASK.TO_MUTE

sp_state_play state 

→

 sp_state_mute state

INTMASK.TO_PAUSE

sp_state_play state 

→

 sp_state_pause state

INTMASK.TO_PLAY

sp_state_idle, mute, pause state 

→

 sp_state_play state

INTMASK.TO_IDLE

sp_state_init, mute, pause, play state 

→

 sp_state_idle state

Memory check INTMASK.TO_PROCESSING mc_state_idle state 

→

 mc_state_ram_rw, ram_march_c, checksum, crc state

INTMASK.TO_IDLE

mc_state_init, mc_state_ram_rw, ram_march_c, checksum, crc state 

→

 mc_state_

idle state

Содержание Buzzer S1C31D51










































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Buzzer S1C31D51

Acclaim Lighting Canvas User Manual preview
Canvas
Бренд: Acclaim Lighting Страницы: 32
Danfoss ERC 211 User Manual preview
ERC 211
Бренд: Danfoss Страницы: 36
Kamstrup M-Bus Manual preview
M-Bus
Бренд: Kamstrup Страницы: 36
RAM RP2000 User Manual preview
RP2000
Бренд: RAM Страницы: 71
TEL AFA4000/1/AS Installation And Calibration Manual preview
AFA4000/1/AS
Бренд: TEL Страницы: 26
Vimar EAM6 Installation And Operation Manual preview
EAM6
Бренд: Vimar Страницы: 32
Ultrahaptics STRATOSTM INSPIRE User Manual preview
STRATOSTM INSPIRE
Бренд: Ultrahaptics Страницы: 7
H3C VCF Installation Manual preview
VCF
Бренд: H3C Страницы: 16
rotork Bifold EHPC210 Firmware Manual preview
Bifold EHPC210
Бренд: rotork Страницы: 22
maxon motor EPOS2 24/5 Hardware Reference Manual preview
EPOS2 24/5
Бренд: maxon motor Страницы: 44
NI RMC-8355 User Manual preview
RMC-8355
Бренд: NI Страницы: 135
Uniteck UNISOLAR 20.24 Manual preview
UNISOLAR 20.24
Бренд: Uniteck Страницы: 46
Gardenic GN-1113 User Manual preview
GN-1113
Бренд: Gardenic Страницы: 14
Atmel Qmatrix Application Note preview
Qmatrix
Бренд: Atmel Страницы: 27
ZEDAR Regency Owner'S Manual preview
Regency
Бренд: ZEDAR Страницы: 25
Elsner Solexa 230V Installation And Adjustment Manual preview
Solexa 230V
Бренд: Elsner Страницы: 52
WifiTrax Model Science WFG-80 Getting Started Manual preview
WFG-80
Бренд: WifiTrax Model Science Страницы: 4
Digital View DD-1920-DUAL-DVI Instructions Manual preview
DD-1920-DUAL-DVI
Бренд: Digital View Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды