Epson Buzzer S1C31D51 Скачать руководство пользователя страница 328 | Manualshive

Страница: 328 / 425

background image

21 HW Processor (HWP) and Sound Output

21-16

Seiko Epson Corporation

S1C31D50/D51 TECHNICAL MANUAL

(Rev. 2.00)

Flash check

The following shows the procedure to execute a Flash check:
1. Confirm that the STATE.STATE[15:0] bits = 0x0001 (mc_state_idle).
2. Confirm that the STATUS.READY bit = 1.

(Command acceptable)

3. Set the COMMAND.COMMAND[7:0] bits to 0x04 or 0x05.*

(Select command)

4. Set the MEMADDR.ADDRESS[31:0] bits.

(Specify check start address)

5. Set the MEMSIZE.SIZE[31:0] bits.

(Specify check size (byte))

6 Set the INITVALUE.INITVALUE[31:0] bits to 0x00000000.

(Specify Flash check initial value)

7. Write 1 to the HWPCMDTRG.HWP0TRG bit.

(Trigger to issue command)

8. Wait until the HWPINTF.HWP0IF bit is set to 1 (interrupt).

(Occurrence of state transition)

The HWP starts the memory check from this point.

9. Confirm that the STATE.STATE[15:0] bits = 0x0004 (mc_state_checksum) or 0x0005 (mc_state_crc) as

necessary.*

10. Write 0 to the HWPINTF.HWP0IF bit.

(Clear interrupt flag)

:

The memory check is in progress.

:

11. Wait until the HWPINTF.HWP0IF bit is set to 1 (interrupt).

(Occurrence of state transition)

The memory check is completed at this point.

12. Confirm that the STATE.STATE[15:0] bits = 0x0001 (mc_state_idle).
13. Write 0 to the HWPINTF.HWP0IF bit.

(Clear interrupt flag)

14. Confirm that the STATUS.PROCESSING[1:0] bits = 0x2 (check completed).
15. Read the RESULT.RESULT[31:0] bits.

(Confirm check result)

These bits hold the checksum or CRC calculation result.

16. Compare the read calculation result with the original value.

*

Two Flash check commands are available. Setting the COMMAND.COMMAND[7:0] bits to 0x04 selects

the Flash Checksum Start command; setting to 0x05 selects the Flash CRC Start command.

Flash Checksum Start command

When this command is issued by the trigger bit, the HWP transits to mc_state_checksum state to calculate
the checksum from the specified Flash data.

Flash CRC Start command

When this command is issued by the trigger bit, the HWP transits to mc_state_crc state to calculate the
CRC from the specified Flash data.

Note: The HWP uses memory mapped access mode (refer to the “Quad Synchronous Serial Interface”

chapter) for the external QSPI-Flash check. Therefore, external Flash memories that do not sup-

port XIP (eXecute-In-Place) cannot be checked.

«
...
326
327
328
329
330
...
»

Содержание Buzzer S1C31D51










































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Buzzer S1C31D51

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: M-Audio Страницы: 26

Бренд: M Climate Страницы: 12

Бренд: Elotech Страницы: 20

Бренд: Intermatic Страницы: 2

Bell & Gossett Technologic PPS

Бренд: Xylem Страницы: 20

Бренд: Aqua Lung Страницы: 24

SUNSAVER SS-10-12V

Бренд: Morningstar Страницы: 26

Бренд: NovaStar Страницы: 11

Бренд: E+L Страницы: 62

Бренд: Omicron Страницы: 17

Бренд: Simplex Страницы: 12

Бренд: TDSi Страницы: 71

Бренд: Azbil Страницы: 68

Бренд: Ltech Страницы: 2

MOVIFIT SC series

Бренд: SEW Страницы: 148

Бренд: Aurora Scientific Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды