ENSONIQ ASR-X PRO, Руководство пользователя

Страница: 41 / 74

Insert Effect Parameters
ENSONIQ ASR-X Pro UserÕs Guide 33
11
1 1222 2 RRR Reeeevvvv →
C C
C Chhhhoooorrrruuuussss
Combines a plate reverb with a stereo chorus.
PPP Paaaarrrraaaam m m meeeetttteeeerrrr RRR Raaaannnnggggeeee D D D Deeeessssccccrrrriiiippppttttiiiioooonnnn
Decay 0.0sec to 10.0sec Controls the amount of time it takes for the
reverberation to decay after the input signal stops.
HF Damping 100Hz to 21.2kHz Controls the rate of attenuation of high frequencies in
the decay of the reverberation. Increasing the value of
this parameter will gradually filter out (dampen) more
and more high frequency energy.
HF Bandwidth 100Hz to 21.2kHz The high frequency bandwidth acts as a low pass filter
on the signal going into the reverb, controlling the
amount of high frequencies that will pass into the effect.
The higher the setting, the more high frequencies are
allowed to pass.
Diffusion 1 0 to 100 Smears the input signal transients, to diffuse and
smooth the sound. Lower values will cause impulse
sounds to appear as a series of discrete echoes, while
higher values tend to increase the smear (smoother
sounding with fewer discrete echoes). We recommend
settings of 50 for starters.
Diffusion 2 0 to 100 This parameter, similar to and in series with Diffusion 1,
performs the same way but controls lower frequency
ranges. Experiment with different levels between the
diffusion parameters to find the settings that are right
for your source.
Definition 0 to 100 Controls the rate at which echo density is increased with
time. Setting this parameter too high can cause the echo
density to build at a rate which exceeds the decay rate.
Chorus Mix Full Dry to Full Wet Controls the dry/wet mix of the chorus.
LFO Rate 1/1 Sys to 1/32 Sys, 0.0Hz
to 20.0Hz
Controls the rate of pitch modulation to the chorus.
LFO Shape Triangle, Sine, Sawtooth,
Square, Asym, 16-Step, 8-
Step, 4-Step
Determines the shape that the LFO will use for pitch
modulation.
LFO Phase -180deg to +180deg Controls the relative phase between left & right LFOs.
Chorus Depth 0.0ms to 25.0ms Controls the amount of modulation.
Chorus Center 0.0ms to 50.0ms Controls the delay times within the chorus. Adjusting
this parameter will change the tonal character of the
chorus.
System
Feedback
-99% to +99% Controls the amount of feedback applied from the
output of the chorus to the input of the reverb.
11 1 1333 3 RRRReeeevvvv → FFFFllllaaaannnnggggeeeerrrr
This insert effect features a plate reverb with a flanger effect.
PPP
Paaaarrrraaaam
m
m meeeetttteeeerrrr
RRR
Raaaannnnggggeeee
D D
D Deeeessssccccrrrriiiippppttttiiiioooonnnn
Decay 0.0sec to 10.0sec Controls the amount of time it takes for the reverb to
decay after the input signal stops.
HF Damping 100Hz to 21.2kHz Controls the rate of attenuation of high frequencies in
the decay of the reverberation. Increasing the value of
this parameter will gradually filter out (dampen) more
and more high frequency energy.
HF Bandwidth 100Hz to 21.2kHz The high frequency bandwidth acts as a low pass filter
on the signal going into the reverb, controlling the
amount of high frequencies that will pass into the effect.
The higher the setting, the more high frequencies are
allowed to pass.