ENSONIQ ASR-X PRO, Руководство пользователя

Страница: 49 / 74

Insert Effect Parameters
ENSONIQ ASR-X Pro UserÕs Guide 41
LFO Rate 1/1 Sys to 1/32 Sys, 0.0Hz
to 20.0Hz
Controls the rate of the modulation applied to the flange
effect.
LFO Shape Triangle, Sine, Sawtooth,
Square, Asym, 16-Step, 8-
Step, 4-Step
Determines the shape that the LFO will use for pitch
modulation.
LFO Phase -180deg to +180deg Controls the relative phase between left and right LFOs.
Flanger Depth 0.0ms to 25.0ms Controls the range of the high-to-low frequency sweep
in the flanger effect.
FlangerCenter 0.0ms to 50.0ms Sets the sweep mid-point of the flanger effect.
Notch Depth 0% to 100% Controls the depth of the peaks and notches produced
by the flanger. This parameter should be set to 100% for
maximum effect.
Feedback -99% to +99% Controls the amount of feedback applied to the flanger.
Positive or negative values will impart a different
tonality to the flange effect, either accenting the peaks or
the notches.
22 2 2222 2 D D D DD D D DLLLL → PPP Phhhhaaaasssseeeerrrr
Combines a digital delay with a phase shifter.
PPP
Paaaarrrraaaam
m
m meeeetttteeeerrrr
RRR
Raaaannnnggggeeee
D D
D Deeeessssccccrrrriiiippppttttiiiioooonnnn
Dly1 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the first independent delay.
Dly1 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly1 Feedback -99% to +99% Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly1 Damping 100Hz to 21.2kHz Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly1 Pan Full <L to Full >R Determines the location of the delay in the stereo
spectrum.
Dly2 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the second independent delay.
Dly2 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly2 Feedback -99% to +99% Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly2 Damping 100Hz to 21.2kHz Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly2 Pan Full <L to Full >R Determines the location of the delay in the stereo
spectrum.
Dly3 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the third independent delay.
Dly3 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly3 Pan Full <L to Full >R Determines the location of the delay in the stereo
spectrum.
Dly4 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the fourth independent delay.
Dly4 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly4 Pan Full <L to Full >R Determines the location of the delay in the stereo
spectrum.