Insert Effect Parameters
42
ENSONIQ ASR-X Pro UserÕs Guide
LFO Rate
1/1 Sys to 1/32 Sys, 0.0Hz
to 20.0Hz
Controls the rate of the modulation applied to the
phaser.
LFO Shape
Triangle, Sine, Sawtooth,
Square, Asym, 16-Step, 8-
Step, 4-Step
Determines the shape that the LFO will use for pitch
modulation.
Phaser Depth
0 to 100
Controls the amount of modulation applied to the
phaser.
Phaser Center
0 to 100
This parameter controls the mid-point of the phaser.
Notch Depth
0% to 100%
Controls the depth of the peaks and notches produced
by the phaser. This parameter should normally be set to
100%.
Feedback
-99% to +99%
Controls the amount of feedback applied to the phaser.
Positive or negative values will impart a different
tonality to the phaser effect, either accenting the peaks
or the notches.
22
2
2333
3 D
D
D
DD
D
D
DLLLL
→
EEEEQ
Q
Q
Q
Combines a digital delay with a parametric EQ.
PPP
Paaaarrrraaaam
m
m
meeeetttteeeerrrr
RRR
Raaaannnnggggeeee
D
D
D
Deeeessssccccrrrriiiippppttttiiiioooonnnn
Dly1 Time
1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the first independent delay.
Dly1 Level
Off, -49.5dB to +12.0dB
Adjusts the volume of the delayed signal against the
original dry signal.
Dly1 Feedback
-99% to +99%
Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly1 Damping
100Hz to 21.2kHz
Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly1 Pan
Full <L to Full >R
Determines the location of the delay in the stereo
spectrum.
Dly2 Time
1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the second independent delay.
Dly2 Level
Off, -49.5dB to +12.0dB
Adjusts the volume of the delayed signal against the
original dry signal.
Dly2 Feedback
-99% to +99%
Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly2 Damping
100Hz to 21.2kHz
Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly2 Pan
Full <L to Full >R
Determines the location of the delay in the stereo
spectrum.
Dly3 Time
1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the third independent delay.
Dly3 Level
Off, -49.5dB to +12.0dB
Adjusts the volume of the delayed signal against the
original dry signal.
Dly3 Pan
Full <L to Full >R
Determines the location of the delay in the stereo
spectrum.
Dly4 Time
1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the delay time for the fourth independent delay.
Dly4 Level
Off, -49.5dB to +12.0dB
Adjusts the volume of the delayed signal against the
original dry signal.
Dly4 Pan
Full <L to Full >R
Determines the location of the delay in the stereo
spectrum.
EQ Input
Off, -49.5dB to +24dB
Adjusts the input level trim to the EQs to eliminate the
possibility of clipping boosted signals.
Содержание ASR-X PRO
