ENSONIQ ASR-X PRO, Руководство пользователя

Страница: 55 / 74

Insert Effect Parameters
ENSONIQ ASR-X Pro UserÕs Guide 47
LoShelf Fc 10Hz to 20.0kHz Sets the center of the low frequency EQ.
LoShelf Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this low
frequency shelf.
Mid 1 Fc 10Hz to 20.0kHz Sets the center of the mid frequency parametric.
Mid 1 Q 1.0 to 40.0 This parameter is a bandwidth control that determines
the width of the resonant peak at the center frequency
band. This parameter is equal to the cutoff frequency
divided by the bandwidth. By raising the value, you can
produce a narrower bandwidth.
Mid 1 Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this mid
frequency band.
Mid 2 Fc 10Hz to 20.0kHz Identical to the Mid 1 Fc parameter, and is used to
control different bandwidths within the mid range.
Mid 2 Q 1.0 to 40.0 Identical to the Mid 1 Q parameter, and is used to
control different bandwidths within the mid range.
Mid 2 Gain Off, -49.5dB to +24dB Identical to the Mid 1 Gain parameter, and is used to
control different bandwidths within the mid range.
HiShelf Fc 10Hz to 20.0kHz Sets the center frequency of the high frequency shelf.
HiShelf Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this high
frequency shelf.
EQ Output Off, -49.5dB to +24dB Controls the gain coming out of the parametric EQ.
LFO Rate 1/1 Sys to 1/32 Sys, 0.0Hz
to 20.0Hz
Controls the rate of the modulation applied to the
phaser.
LFO Shape Triangle, Sine, Sawtooth,
Square, Asym, 16-Step, 8-
Step, 4-Step
Determines the shape that the LFO will use for pitch
modulation.
Phaser Depth 0 to 100 Controls the amount of modulation applied to the
phaser.
Phaser Center 0 to 100 This parameter controls the mid-point of the phaser.
Notch Depth 0% to 100% Controls the depth of the peaks and notches produced
by the phaser. This parameter should normally be set to
100%.
Feedback -99% to +99% Controls the amount of feedback applied to the phaser.
Positive or negative values will impart a different
tonality to the phaser effect, either accenting the peaks
or the notches.
22 2 2888 8 D D D Diiiisssstttt → A A A AuuuuttttooooW W W Waaaahhhh
Dist
→
AutoWah combines a voltage control filter and a raspy distortion, and a second voltage controlled
filter. Three effects can be obtained: distortion, wah-wah, and auto-wah. The last two functions use the
same VCF. These filters can be disabled or used as EQ if desired. There is a second VCF that exists after
the distortion that can be set to act like a simple speaker simulator.
PPP
Paaaarrrraaaam
m
m meeeetttteeeerrrr
RRR
Raaaannnnggggeeee
D D
D Deeeessssccccrrrriiiippppttttiiiioooonnnn
Pre HPF Fc 10Hz to 1.50kHz Filters out the low frequencies before the EQ. The higher
the value, the less low frequencies will pass through.
Pre VCF Fc 10Hz to 7.10kHz Determines the distortion filter cutoff frequency. Higher
values have a brighter sound. This parameter can be
modulated by any continuous MIDI controller for a
wah-wah pedal effect.
Pre VCF Q 1.0 to 40.0 Determines the level and width of the resonant peak at
the filter cutoff point. While the Fc (filter cutoff)
parameter determines where (at what frequency) this
peak will occur, the Q setting controls the sharpness of
the peak.