ENSONIQ ASR-X PRO, Руководство пользователя

Страница: 61 / 74

Insert Effect Parameters
ENSONIQ ASR-X Pro UserÕs Guide 53
Dist Volume Off, -99dB to 0.0dB Controls the volume of the distortion effect. Generally, if
the distortion gain is set high, set this parameter lower.
Dist LPF Fc 10Hz to 20.0kHz Filters out high frequencies prior to the distortion.
Post VCF Fc 10Hz to 7.10kHz Determines the distortion filter cut off frequency. Higher
values have a brighter sound. This parameter can be
modulated by any continuous MIDI controller for a
wah-wah pedal effect.
Post VCF Q 1.0 to 40.0 Determines the level and width of the resonant peak at
the filter cutoff point. While the Fc (filter cutoff)
parameter determines where (at what frequency) this
peak will occur, the Q setting controls the sharpness of
the peak.
Dist Offset -99% to +99% Adjusts the balance of even-to-odd-generated
harmonics.
Dist Curve Soft, Medium 1, Medium 2,
Hard, Buzz
Selects the type of clipping produced by the distortion.
The curves range from tube-like distortion (Soft) to
nasty distortion (Buzz).
Dist Dry Lev Off, -49.5dB to 0.0dB Controls the amount of dry signal to be mixed with the
distorted signal.
VCF Input Off, -49.5dB to 0.0dB Trims the input to the formant filter so that clipping
does not occur.
VCF Dry Amt Off, -49.5dB to +24dB Controls the level of the distortion/DDL signal to be
mixed with the output of the formant filter.
Shape 1 A, E, I, O, U, AA, AE, AH,
AO, EH, ER, IH, IY, UH,
UW, B, D, F, G, J, K, L, M,
N, P, R, S, T, V, Z
Selects the shape of the first formant filter.
Shape 2 A, E, I, O, U, AA, AE, AH,
AO, EH, ER, IH, IY, UH,
UW, B, D, F, G, J, K, L, M,
N, P, R, S, T, V, Z
Selects the shape of the second formant filter.
FormantWarp -12 to +12 semi Shifts all formant frequencies up or down, warping the
ÒsizeÓ of the formant filter.
AutoPan Depth 0% to 100% Controls the depth of the auto-panning function after
the formant filter.
LFO Rate 1/1 Sys to 1/32 Sys, 0.0Hz
to 20.0Hz
This parameter controls the rate of pitch modulation
which creates a chorusing effect. To achieve chorusing,
this rate must be very low.
LFO Shape Triangle, Sine, Sawtooth,
Square, Asym, 16-Step, 8-
Step, 4-Step
Determines the shape that the LFO will use for pitch
modulation.
LFO Phase -180deg to +180deg Controls the relative phase between left and right LFOs.
Dly1 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the amount of delay time for the first independent
delay.
Dly1 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly1 Feedback -99% to +99% Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.
Dly1 Damping 100Hz to 21.2kHz Controls the cutoff of a low pass filter on the feedback
signal, which adjusts the amount of damping to the
feedback signals. The lower the number, the more the
signals are damped.
Dly2 Time 1/1 Sys to 1/32 Sys, 0ms to
630ms
Sets the amount of delay time for the second
independent delay.
Dly2 Level Off, -49.5dB to +12.0dB Adjusts the volume of the delayed signal against the
original dry signal.
Dly2 Feedback -99% to +99% Determines the amount of signal that will be fed from
the output back into the input, increasing the number of
repeats in the delay.