ENSONIQ ASR-X PRO, Руководство пользователя

Страница: 68 / 74

Insert Effect Parameters
60 ENSONIQ ASR-X Pro UserÕs Guide
33
3 3888 8 C
C
C Coooom
m
m mpppp →
D D
D Diiiisssstttt →
D D
D DD
D
D DLLLL
A bright guitar-effects chain that features compression, gate, voltage-controlled distortion, parametric
EQ, and a digital delay.
PPP Paaaarrrraaaam m m meeeetttteeeerrrr RRR Raaaannnnggggeeee D D D Deeeessssccccrrrriiiippppttttiiiioooonnnn
Comp Ratio 1.0:1 to INF:1 Sets the amount of compression. The range is based on
decibels (dB) above the threshold. If set to 4:1 for
example, it will allow 1 dB increase in output level for
every 4 dB increase in input level. When set to infinity, it
acts as a limiter.
Comp Attack 50us to 10.0s Determines the time after the initial signal has been
detected and before the compression takes affect.
Comp Release 50us to 10.0s Determines how long it takes for the compression to be
fully deactivated after the input signal drops below the
threshold level. This is generally set longer than the
attack time.
Comp Thresh -96.0dB to 0.0dB Sets the threshold level. Signals that exceed this level
will be compressed, while signals that are below will be
unaffected. To turn off the compressor, set the level to
+00 dB.
Comp Output Off, -49.5dB to +48dB This parameter boosts or cuts the compressed signal
level.
Gate Thresh -96.0dB to 0.0dB Sets the upper threshold level at which the noise gate
passes the audio.
Gate Hysteresis 0dB to 48dB Sets the lower threshold level relative to Gate Thresh,
below which the noise gate shuts off the audio.
Dist LPF Fc 10Hz to 20.0kHz Filters out high frequencies prior to the distortion.
Dist Offset -99% to +99% Adjusts the balance of even-to-odd-generated
harmonics.
Dist Gain Off, -49.5dB to +48dB Controls the gain going into the distortion effect. This
will boost the signal level up to 48 dB. For more
distortion, use a high input level gain and turn the
distortion volume down to keep the volume under
control. For less distortion, use a low gain input level
and a higher output volume.
Dist Curve Soft, Medium 1, Medium 2,
Hard, Buzz
Selects the type of clipping produced by the distortion.
The curves range from tube-like distortion (Soft) to
nasty distortion (Buzz).
Dist Volume Off, -99dB to 0.0dB Controls the volume of the distortion effect. Generally, if
the distortion gain is set high, set this parameter lower.
Post VCF Fc 10Hz to 7.10kHz Determines the filter cut off-frequency after the
distortion. Higher values have a brighter sound. This
parameter can be used to emulate a speaker cabinet.
Post VCF Q 1.0 to 40.0 Determines the level and width of the resonant peak at
the filter cutoff point. While the Post VCF Fc parameter
determines where (at what-frequency) this peak will
occur, this parameter controls the sharpness of the peak.
Dist Dry Lev Off, -49.5dB to 0.0dB Controls the amount of dry signal to be mixed with the
distorted signal.
LoShelf Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to the low
frequency shelf.
Mid 1 Fc 10Hz to 20.0kHz Sets the center of the mid frequency parametric.
Mid 1 Q 1.0 to 40.0 This parameter is a bandwidth control that determines
the width of the resonant peak at the center frequency
band. This parameter is equal to the cutoff frequency
divided by the bandwidth. By raising the value, you can
produce a narrower bandwidth.
Mid 1 Gain Off, -49.5dB to +24dB Sets the amount of boost or cut applied to this mid
frequency band.
Mid 2 Fc 10Hz to 20.0kHz Identical to the Mid 1 Fc parameter, and is used to
control different bandwidths within the mid range.