Enovation Controls Murphy PowerCore MPC-10 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 65

background image

Software Release: [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042;

BTL: 02.09.10015.00]

Section 40

49

00-02-0939

2019-06-13

Passcodes (High Security)

This menu allows the operator using the High Security passcode to see the three 4-digit passcodes for Low,
Medium and High security. This is a visual menu only. The security passcodes are only able to be altered
via PowerVision for Controllers PC tool.

Load Configuration (High Security) MPC-10 ONLY

NOTE:

It is essential that the USB Drive is formatted to a FAT file system before using to

load software. If the drive is not formatted to FAT and left in another format the file may
not load correctly.

This menu allows the MPC-10 operator using the High Security passcode to select a file from a USB drive
plugged into the programming harness for the controller. Once the files are stored on the drive after
generated in PowerVision for Controllers the file will show as long as the software was for the MPC-10
hardware and has the file extension .gcibin. Once the file is found it will show in the screen. Follow directions
on the screen to load desired file. The screen will turn off then all three LEDs will come on then the Amber
LED will begin flashing. Once the file is finished loading the Green LED stays on stead while the Amber and
Red LEDs flash. The USB drive can now be removed to initiate a reboot of the controller or simply cycle
power off then back on.

NOTE:

If the file does not fully load due to the file being corrupt, the controller turned off

during installing file, or the USB drive removed during drive the operator will be required to
load a file created for the MPC-10 named configurationFull.gcibin to recover the controller
from its bootloader mode. Once this is done the operator will be able to load a file from the
menu again following power up.

Figure 20: File Selection

«
...
47
48
49
50
51
...
»

Содержание Murphy PowerCore MPC-10


































































Отзывы:

Нет отзывов

Похожие инструкции для Murphy PowerCore MPC-10

Бренд: Magnescale Страницы: 132

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 20

Бренд: National Instruments Страницы: 102

Бренд: NAU ROBOTICS Страницы: 109

Maschine Mikro MK2

Бренд: Native Instruments Страницы: 181

Бренд: K&G GROEP Страницы: 27

Бренд: CAME Страницы: 2

Бренд: CalAmp Страницы: 13

FAREX SR MINI SYSTEM

Бренд: RKC INSTRUMENT Страницы: 82

Бренд: SMC Networks Страницы: 10

Бренд: Forcepoint Страницы: 15

VPPM-...-LK Series

Бренд: Festo Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды