Enovation Controls Murphy PowerCore MPC-10 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 65

background image

Software Release: [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042;

BTL: 02.09.10015.00]

Section 40

21

00-02-0939

2019-06-13

7. Assign 4-20mA, 0-5V Ambient Temperature or Model 12 as the function for the selected Analog

Input.

8. Press

[Back]

once to return to the Analog Input menu.

9. If 4-20mA or 0-5V Ambient Temperature was selected follow the subsequent procedures below for

sensor setup.

10. Press the arrow up or arrow down key. Select

Sensor Setup

then press

[Enter]

.

11. Select Ambient Temp to set up then press

[Enter]

.

12. Set the offset of the 4mA if needed to calibrate the low side then press

[Enter]

.

13. Set the range of the transducer on the high side then press

[Enter].

(e.g., 32°F -150°F transducer

would show 4mA at 32°F and 20mA at 150°F).

14. Press the

[Menu]

key to exit the menu setup screens.

NOTE:

If an auto stop condition occurs during the warm-up delay, the controller will enter

an auto stop sequence.

Setting

up to Stop the Engine from Utilizing the Countdown

Timer

The MPC-10 / TEC-10 will only utilize this timer when starting in Auto mode. The control and the running of
the engine will continue until the chosen stop condition is met or until the Countdown timer runs out of time.
Once set, the operator will be required to disable or change the timer in the menu in order to eliminate the
countdown timer being active on every auto startup.

1. Access

Menu/Start_Stop Timers/Countdown Timer

.

2. Set the hours, minutes and seconds desired for the running of the engine, and press

[Enter]

.

3. Press the

[Menu]

key to exit the menu setup screens.

NOTE:

When the Countdown Timer is set for a countdown, the controller will always

countdown upon an auto start until the timer is set to 0.

Screen Examples

Figure 8: Screen Example

«
...
19
20
21
22
23
...
»

Содержание Murphy PowerCore MPC-10


































































Отзывы:

Нет отзывов

Похожие инструкции для Murphy PowerCore MPC-10

Бренд: Gardner Denver Страницы: 22

Бренд: B&G Страницы: 2

Бренд: Radware Страницы: 98

Бренд: RabbitCore Страницы: 34

Бренд: Maximum Controls Страницы: 58

Бренд: Anilam Страницы: 31

Бренд: Rinnai Страницы: 7

Бренд: TCS Страницы: 8

Level-Trac LT-310

Бренд: QTS Страницы: 12

fantech ECO-FEEL 414729

Бренд: SystemAir Страницы: 2

Бренд: Zander Aachen Страницы: 44

Бренд: 4D systems Страницы: 6

i-Kiosk 100 Plus

Бренд: FingerTec Страницы: 3

Бренд: Current Страницы: 4

Бренд: PEAS Страницы: 4

Бренд: Sollae Systems Страницы: 72

Бренд: DAAB Страницы: 60

Бренд: BILDA Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды