Enovation Controls Murphy PowerCore MPC-10 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 65

Enovation Controls Murphy PowerCore MPC-10 Скачать руководство пользователя страница 20

Software Release: [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042;

BTL: 02.09.10015.00]

Section 40

20

00-02-0939

2019-06-13

Setting

up to Auto Start on Level

1. Access

Menu/Application Configuration.

Press the down arrow to

Auto Start/Stop Function

then

press

[Enter]

.

2. Utilize the Up and Down arrows to select

Level Transducer

then press

[Enter].

3. Utilize the Up and Down arrows to select

Level Transducer

in the main application configuration

menu.

4. Complete the parameters that apply. (Start/Stop Level and Level Maintain Type, See Menu Glossary

for explanation of settings.)

5. Press

[Back]

twice and access

Input_Output/Analog Inputs.

6.  Select the Analog Input to modify for the level transducer.
7.  Assign 4-20mA System Level as the function for the selected Analog Input.
8.  Press

[Back]

once to get back to the Analog Input menu.

9. Press the arrow up or arrow down key. Select

Sensor Setup

then press

[Enter]

.

10. Select System Level to set up then press

[Enter]

.

11. Set the offset of the 4mA if needed to calibrate the low side then press

[Enter]

.

12. Set the range of the transducer on the high side then press

[Enter].

(i.e., 0-10ft transducer would

show 4mA at 0 ft. and 20mA at 10 ft.)

13. Press

[Back]

twice to return to the main menu.

14. Utilize the Up and Down arrows to select

Advanced Engine Settings

then press

[Enter]

.

15. Utilize the Up and Down arrows to select

Warnings and Shutdowns

then press

[Enter].

16. Utilize the Up and Down arrows to set the

High and Low Level

warnings and shutdowns.

17. Press the

[Menu]

key to exit the menu setup screens.

Setting to Auto Start on Clock

NOTES:

1)

Ensure the correct date and time are established in the System menu prior to
establishing the Auto Start on Clock settings.

2)

The Clock start timer is independent of other auto start start/stop functions. When
started from the clock the controller will shut down the engine from the clock.

1. Access

Menu/Start_Stop Timers

, and select the first Start/Stop Timer.

2.  Select Start Day 1 and then select the appropriate day or Daily.
3.  Select Start Time 1 and establish the hour, minute and second to start.
4.  Establish the Stop Day and Time as in steps 2-3.
5.  Press the

[Menu]

key to exit the menu setup screens.

NOTE:

The MPC-10 / TEC-10 has the ability to establish three different Start/Stop dates

and times. If desired, repeat steps 1-3 for subsequent Timers.

Setting to Auto Start on Temperature

1.

Access

Menu/Application Configuration.

Press the down arrow to

Auto Start/Stop Function

then

press

[Enter]

.

2. Utilize the Up and Down arrows to select

Temperature Transducer

then press

[Enter].

3. Utilize the Up and Down arrows to select

Temperature Transducer

in the main application

configuration menu.

4. Establish a Start and Stop Temperature, and press

[Back]

twice.

5. Utilize the Up and Down arrows to select

Input_Output/Analog Inputs

then press

[Enter].

6. Select the Analog Input to modify for the temperature transducer.

«
...
18
19
20
21
22
...
»

Содержание Murphy PowerCore MPC-10


































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды