Enovation Controls Murphy PowerCore MPC-10 Скачать руководство пользователя страница 17

Страница: 17 / 65

Software Release: [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042;

BTL: 02.09.10015.00]

Section 40

00-02-0939

2019-06-13

Quick-Start Setup

The following sections provide a walk-through of the steps necessary for some of the various configurations
and settings available on the MPC-10 / TEC-10 Controller.

Cycling power to the controller is

recommended after making changes to set points.

Stepping through the Menu will be depicted as follows:

Menu/System/Contrast directs the operator to go into the Menu first, then look for a parameter titled System
and press

[Enter]

to go into the System menu. Then look for a parameter titled Contrast and press

[Enter]

to go into the Contrast menu, etc.

Mechanical Engine Setup

1. Access

Menu/Engine Settings/Engine Type,

and select Mechanical then press

[Enter]

2. Press down arrow to

Engine Manufacturer

, select which engine manufacturer the controller is/will be

used then press

[Enter]

3. Press down arrow to

Speed Source

, and select either Alternator or Magnetic Pickup then press

[Enter]

4. Press down arrow to

Speed Calibration,

press

[Enter]

5. Utilize the Up and Down arrows to establish the appropriate number of flywheel teeth or engine

alternator pulses, and press

[Enter]

6. Press the

[Back]

key and down arrow to

Throttle

, and press

[Enter]

7. Press

[Enter]

to access

Manual Throttle Method,

select throttle type if throttling the engine from the

controller for manually throttling the engine Inc/Dec, Run/Idle, Preset 3, or Preset 4 and press

[Enter]

8. Press down arrow to

Engine Throttle Type

, select Pulse Inc/Dec or None and press

[Enter]

9. Press down arrow to

Target RPM Step Size

, select appropriate step size then press

[Enter]

10. Press down arrow to

Throttle Deadband RPM

, select appropriate deadband then press

[Enter]

11. Press down arrow to

Throttle Inc/Dec Pulse

, select appropriate pulse time then press

[Enter]

12. Press down arrow to

Throttle Inc/Dec Pulse Delay

, select appropriate pulse delay then press

[Enter]

13. Press down arrow to

Throttle Inc Rate

, select appropriate throttle increment rate then press

[Enter]

14. Press down arrow to

Throttle Dec Rate

, select appropriate throttle decrement rate then press

[Enter]

15. Press the

[Back]

key, and down arrow to

Input/Output

, and press

[Enter]

16. Access

Analog Inputs

and assign one Analog input for Oil Pressure and one for Engine Temperature.

Press

[Enter]

to save the settings.

17. Press

[Back]

and access Relay and Digital Outputs.

18. Press down arrow to

Relay1-3 or DO1-4

, and assign desired outputs for Crank, Fuel, and Inc/Dec

outputs if throttle type selected was Inc/Dec.

NOTE:

DO3 and DO4 are factory set to Throttle Decrease and Throttle Increase to be

used with the Murphy AT03069 Throttle Actuator.

19. Press the

[Back]

key and up arrow to

Advanced Engine Settings

, and press

[Enter].

20. Press down arrow to

Warnings and Shutdowns

, press

[Enter]

21. Ensure all warnings and shutdowns are set to the appropriate settings for the engine for engine faults

such as oil pressure and coolant temperature.

22. Press the

[Back]

key twice and up arrow to

System

, and press

[Enter].

23. Press down arrow to

Set Machine Hours,

select desired machine/internal hours then press

[Enter]

24. Press the

[Menu]

key to exit the menu setup screens.

Содержание Murphy PowerCore MPC-10


































































Результаты поиска

Содержание Murphy PowerCore MPC-10

Отзывы:

Похожие инструкции для Murphy PowerCore MPC-10

Бренды по названию

Популярные бренды

Enovation Controls Murphy PowerCore MPC-10, Руководство по эксплуатации

Результаты поиска

Содержание Murphy PowerCore MPC-10

Отзывы:

Похожие инструкции для Murphy PowerCore MPC-10

Бренды по названию

Популярные бренды