Enovation Controls Murphy PowerCore MPC-10 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 65

background image

Software Release: [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042;

BTL: 02.09.10015.00]

Section 40

48

00-02-0939

2019-06-13

Exercise Running Loaded Time

(Medium Security)

:

Time the operator sets for the engine to run if

voltage drops below the low voltage set point.

Factory set to 15 minutes

Communication (High Security)

Communication Type

(High Security)

:

PVA Gauge:

this function will be used if utilizing PVA Gauges on the RS485 Communications

Port.

Modbus:

this function will be used if using a SCADA or telemetry device for polling the Modbus

register list on the RS485 Communications Port. See Modbus Register Map.

Factory

Default.

Slave Address

(High Security)

:

This is the RS485 Modbus slave node number.

Factory set to 1

.

Serial Setup

(High Security)

:

Allows the operator to change the controller’s RS485 serial communication

settings.

Baudrate

(High Security)

:

Factory set to 19200

9600
19200

38400
57600
115200

Stopbits

(High Security)

:

Factory set to 1

0
1

2

Parity

(High Security)

: Factory set to None

None

Odd
Even

PV CAN Backlight Enable

(High Security)

:

allows the MPC-10 / TEC-10 to control the backlights of the

PVCAN gauges when used with the controller.

Factory set to Off

CAN Termination

(High Security)

:

allows the operator to enable or disable the controller’s internal 120 ohm

terminating resistor. This should be enabled if the MPC-10 / TEC-10 is located at the end of the CAN
bus and the end terminating resistor is not in the harness.

Factory set to Enable.

CAN Parameter Map

(High Security)

:

allows the operator to enable or disable the proprietary CAN

parameter map. The CAN Parameter Map can be used in place of the Modbus map when using a
CAN device to talk to the controller for starting, stopping and control functions via telematics or
another CAN based system. See CAN Parameter Map Section below for definition of the mapping.

Factory set to Disable.

CAN Baud rate

(High Security)

:

Factory set to 250 Kbps

10 Kbps
20 Kbps
50 Kbps
100 Kbps
125 Kbps
250 Kbps
500 Kbps
800 Kbps
1 Mbps

«
...
46
47
48
49
50
...
»

Содержание Murphy PowerCore MPC-10


































































Отзывы:

Нет отзывов

Похожие инструкции для Murphy PowerCore MPC-10

Бренд: Canon Страницы: 2

Бренд: EA Страницы: 24

Бренд: Jafar Страницы: 9

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 32

Бренд: 2gig Technologies Страницы: 4

Бренд: 2gig Technologies Страницы: 2

Бренд: G1SLE Страницы: 2

Бренд: Danfoss Страницы: 37

Бренд: Daikin Страницы: 44

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 52

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

8271 Nways Ethernet LAN Switch

Бренд: IBM Страницы: 6

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды