Enovation Controls Murphy PowerCore MPC-10 Скачать руководство пользователя страница 29

Страница: 29 / 65

Software Release: [App: 02.09.10051.00; Config: 2.9.20024; Built in PowerVision Configuration Studio Version: 2.9.23042;

BTL: 02.09.10015.00]

Section 40

00-02-0939

2019-06-13

Brightness

(Medium Security)

allows the backlight of the screen to be adjusted.

Factory set to 90.

Parameter Setup

(Low Security)

allows four-up Page 1 and Page 2 parameters to be changed without

using a PC.

Backlight Control

(Medium Security)

turns off (disables) or on (enables) the screen’s backlight.

Factory

set to Enable.

Standby Timer

(Medium Security)

allows the screen the designated amount of time before the controller

goes into Standby mode. Standby is also referred to as sleep mode.

Factory set to 00:30:00.

Service Reminders

(Medium Security)

when the service reminder is set to 0, the alarms will be disabled;

however, the countdown will continue and will show the numbers as (-) numbers as it counts down past 0
for the following parameters:

All service reminders factory set to 0.0 Hrs. If service reminders are

desired they should be set within this menu.

Show Service Screens

(Medium Security)

factory set to Hide.

Oil Life

(Medium Security)

factory set to 0 Hrs

Reset Oil Life

(Medium Security)

resets Oil Life reminder to factory setting.

Oil Filter Life

(Medium Security)

factory set to 0 Hrs

Reset Oil Filter Life

(Medium Security)

resets Oil Filter Life reminder to factory setting.

Belt Life

(Medium Security)

factory set to 0 Hrs

Reset Belt Life

(Medium Security)

resets Belt Life reminder to factory setting.

Battery Life

(Medium Security)

factory set to 0 Hrs

Reset Battery Life

(Medium Security)

resets Battery Life reminder to factory setting.

Fuel Filter Life

(Medium Security)

factory set to 0 Hrs

Reset Fuel Filter Life

(Medium Security)

resets Fuel Filter Life reminder to factory setting.

Air Filter Life

(Medium Security)

factory set to 0 Hrs

Reset Air Filter Life

(Medium Security)

resets Air Filter Life reminder to factory setting.

Overhaul Life

(Medium Security)

factory set to 0 Hrs

Reset Overhaul Life

(Medium Security)

resets Overhaul Life reminder to factory setting.

Reset All

(Medium Security)

Resets all service reminders to factory setting.

ECU Fault Codes

(Medium Security)

allows the operator to request stored fault codes from the ECU

and request to clear active as well as stored codes in the ECU.

Stored Fault Codes

(Medium Security)

allows the operator to query the Engine ECU for review

of its stored fault codes.

Clear Active ECU Fault Codes

(High Security)

Clears any active fault codes broadcast from the

ECU as long as the ECU accepts the request.

Clear Stored ECU Fault Codes

(High Security)

Clears any stored fault codes in the ECU as

long as the ECU accepts the request.

Auto / Manual

(Low Security)

Содержание Murphy PowerCore MPC-10


































































Результаты поиска

Содержание Murphy PowerCore MPC-10

Отзывы:

Похожие инструкции для Murphy PowerCore MPC-10

Бренды по названию

Популярные бренды

Enovation Controls Murphy PowerCore MPC-10, Руководство по эксплуатации

Результаты поиска

Содержание Murphy PowerCore MPC-10

Отзывы:

Похожие инструкции для Murphy PowerCore MPC-10

Бренды по названию

Популярные бренды