Endress+Hauser Solitrend MMP20 Скачать руководство пользователя страница 53

Страница: 53 / 56

Solitrend MMP20 (Option D)

Technical data

Hauser

Technical data

12.1 Handheld device

• Height: 36 mm

• Width: 64 mm

• Length: 150 mm

• Weight: (with battery) approx. 437 g

• Power demand:

• Power down: 35 µA

• Idle:

- Background lighting off: 26 mA

- Background lighting on: 56 mA

• Probe switched on: 100 mA

• Measurement: 350 mA

• Measurements per charge: up to approx. 5000 (20 °C / background lighting max.)

• Probes that can be connected: SWZ, S1, S1C, S2

• Storage temperature: –20 to +70 °C (–4 to +158 °F)

• Operating temperature: –20 to +70 °C (–4 to +158 °F)

• Charging temperature: 10 to 30 °C (50 to 86 °F)

• Charging voltage: nom. 12 V, max. 15 V, min. 12 V

• Charging current: approx. 1 A

• Charging time: approx. 2 hours if battery fully discharged

• Accumulator: Ni-MH (4 × 1.2 V) (AA), 2

000 mA/h, >1000 measurements

• Physical BUS: RS485

• Bus protocol: IMP-BUS protocol II

12.2 SWZ probe

• Power supply: 12 to 24 V

• Current consumption: 150 mA @ 12 V

during 2 to 3 s measuring cycle time

• Measuring range: 0 to 100 % vol. water content

• Repeatability, water content measurement (with probe at rest in concrete): ±2 l/m³

• Absolute accuracy: ±3 % of the water quantity

• Conductivity range: 0 to 20 dS/m

• Measuring volume: 0.5 l

• Probe temperature range: 0 to 50 °C (32 to 122 °F)

• Calibration:

• Pre-programmed calibrations for fresh concrete

• Own calibrations possible

• Up to 15 calibration curves can be saved in memory

• Degree of protection: IP68

• Dimensions: 155 mm× 60 mm

• Interfaces: 1.5 m cable with 7-pin coupling socket

12.3 S1 probe

For moisture measurement of bulk solids such as sand and gravel

• Sensor with integrated TDR electronics

• Screw thread: M28 × 1.5 (on cable side)

Содержание Solitrend MMP20

























































Результаты поиска

Содержание Solitrend MMP20

Отзывы:

Похожие инструкции для Solitrend MMP20

Бренды по названию

Популярные бренды

Endress+Hauser Solitrend MMP20, Руководство по эксплуатации

Результаты поиска

Содержание Solitrend MMP20

Отзывы:

Похожие инструкции для Solitrend MMP20

Бренды по названию

Популярные бренды