Endress+Hauser Solitrend MMP20 Скачать руководство пользователя страница 49

Страница: 49 / 56

Solitrend MMP20 (Option D)

S1 moisture probe

Hauser

Take the measurements according to the following procedure:

1. Fill the container with sand



A0040894

2. Lift the container approximately 5 cm and then drop it. Repeat this five times (more

if necessary).
 This packs (compresses) the sand.

A0040895

3. Insert the probe into the sand. Once the base of the probe reaches the sand surface

push the probe in slightly further (do not jiggle the probe or turn it while inserting

it!). In the case of gravel and grit, shake the container while introducing the probe.

Otherwise it is very difficult to introduce the probe into the material. Shaking the

container places the material optimally around the probe rods.


A0040896

A0040897

Содержание Solitrend MMP20

























































Результаты поиска

Содержание Solitrend MMP20

Отзывы:

Похожие инструкции для Solitrend MMP20

Бренды по названию

Популярные бренды

Endress+Hauser Solitrend MMP20, Руководство по эксплуатации

Результаты поиска

Содержание Solitrend MMP20

Отзывы:

Похожие инструкции для Solitrend MMP20

Бренды по названию

Популярные бренды