Endress+Hauser Solitrend MMP20 Скачать руководство пользователя страница 23

Страница: 23 / 56

Solitrend MMP20 (Option D)

Commissioning

Hauser

1. Select the desired automatic switch-off time by pressing the navigation key several

times

2. Select the desired brightness of the display or switch it off completely by pressing the

navigation key several times

3. Press Enter to activate and save the selected settings

 Once the setting has been activated, the symbol appears in the top right-hand

corner

7.9.6

Display contrast

At extreme temperatures, it may be necessary to change the contrast setting to improve

screen readability.

 14

Display contrast

1. Using the navigation keys

, set the contrast so that you can clearly see all the

gray gradations in the bar chart.

2. Press Enter to activate and save the selected setting

 Once the setting has been activated, the symbol appears in the top right-hand

corner

7.9.7

Probe info

The following information about the connected probe is displayed in the "Probe info" menu

item:

• Serial number

• Probe type

• Hardware version (HW)

• Firmware version (FW)

7.9.8

Info

The following information about the handheld device is displayed in the "Info" menu item:

• Serial number

• Hardware version (HW)

• Firmware version (FW)

• Battery capacity

• Battery voltage

7.9.9

Material calibration curves

The SWZ probe can be set to another material calibration curve in the "Material calibration

curves" menu item.
When the device is switched on, the calibration curve configured in this menu item is

displayed for approx. 3 s at the bottom of the screen.
Overall, up to 15 calibration curves can be managed for materials such as suspensions,

sludges etc.

Содержание Solitrend MMP20

























































Результаты поиска

Содержание Solitrend MMP20

Отзывы:

Похожие инструкции для Solitrend MMP20

Бренды по названию

Популярные бренды

Endress+Hauser Solitrend MMP20, Руководство по эксплуатации

Результаты поиска

Содержание Solitrend MMP20

Отзывы:

Похожие инструкции для Solitrend MMP20

Бренды по названию

Популярные бренды