Endress+Hauser Solitrend MMP20 Скачать руководство пользователя страница 44

Страница: 44 / 56

S1 moisture probe

Solitrend MMP20 (Option D)

Hauser

3. Select the percentage moisture using the navigation keys



4. Press the Enter key

 The setting is accepted

5. Press the Enter key again

 The material measurement process is started

Four measurements are taken in order to increase the accuracy. An average of

these measurement values is then calculated. The measuring time is

approximately 20 seconds. When the measurement is finished, the measured

pulse transit time is displayed briefly.

6. After this, the calibration can be saved to the calibration memory set at the start

("Save").


7. Press the Enter key

 The selected memory is overwritten.

The word "OWN:" now appears in front of the original memory name to clearly

indicate which memory has been overwritten.

NOTICE

If "SAVE" is selected at the end of the calibration, one of the pre-configured (or already

modified) calibrations in the probe is overwritten!

‣

The original calibrations can only be restored by our Service Department.

Before the measurement commences, make sure that the rods of the probe are fully

immersed in the material to be measured. The probe must remain in the material for

the entire duration of the measurement and should not be moved.

2-point calibration:

In a 2-point calibration, two material samples of different moisture content are measured

and a linear equation (f(x)=mx+b) is then calculated from this information. While a

Содержание Solitrend MMP20

























































Результаты поиска

Содержание Solitrend MMP20

Отзывы:

Похожие инструкции для Solitrend MMP20

Бренды по названию

Популярные бренды

Endress+Hauser Solitrend MMP20, Руководство по эксплуатации

Результаты поиска

Содержание Solitrend MMP20

Отзывы:

Похожие инструкции для Solitrend MMP20

Бренды по названию

Популярные бренды