Endress+Hauser Solitrend MMP20 Скачать руководство пользователя страница 40

Страница: 40 / 56

S1 moisture probe

Solitrend MMP20 (Option D)

Hauser

S1 moisture probe

The handheld device can be used in conjunction with the S1 probe to measure

moisture in sand, gravel and other bulk solids.

11.1 Connecting the S1 probe

1. Connect the S1 probe to the handheld device

 Insert the 7-pin plug into the socket provided on the handheld device

2. Tighten the coupling nut

 The handheld device detects the probe automatically

Meaning of displayed text:

•

Cal.:

number of the active calibration in the probe

•

Moisture:

moisture measured value

•

EC-T:

electrical conductivity based on TDR measurement

•

Serial No.:

serial number of the probe

•

HW:

hardware version

•

FW:

firmware version

11.2 Measurement

The handheld device operates in the "Average" operating mode in connection with

the S1 probe.

"Average" operating mode:

in the "Average" operating mode, the device displays the

average moisture value calculated from up to 6 individual measurements

No additional actions are possible during a measurement. The user must wait until

the measurement is finished.

11.2.1 "Average" operating mode

In this mode, only the moisture is determined and an arithmetic average is calculated from

up to six individual values. The gravimetric moisture is displayed here. This operating

mode is suitable for measuring the moisture values of large volumes of material (e.g. sand,

gravel etc.).
After switching on the handheld device, the following screen is displayed in the "Average"

operating mode after the initial start-up screen:

Individual measurement values

Number of the selected calibration

Remaining battery capacity

Average of the measurements

Содержание Solitrend MMP20

























































Результаты поиска

Содержание Solitrend MMP20

Отзывы:

Похожие инструкции для Solitrend MMP20

Бренды по названию

Популярные бренды

Endress+Hauser Solitrend MMP20, Руководство по эксплуатации

Результаты поиска

Содержание Solitrend MMP20

Отзывы:

Похожие инструкции для Solitrend MMP20

Бренды по названию

Популярные бренды