manualshive.com logo in svg

Eaton Compass, Руководство по установке, Страница: 54 / 62

Поделиться
Скачать
Eaton Compass Скачать руководство пользователя страница 54

50

Compass

Installation Manual

COMPASS INSTALLATION MANUAL

         www.eaton.com/compass

Install Corner Worksurfaces

Corner worksurfaces are delivered with two 

appropriate length stretchers.

Requirements:

•   

Installed legs, stretchers, organizer uprights, panels, 

overhead storage compartments, shelves and doors

Components:

•  

Corner worksurface

Hardware - COMPKIT5

•   

#10-32 x 

3

⁄

4

 wood screws 

Tools required (not included)

•   

Powered driver

•  

#2 Phillips bit

Complete this procedure to install corner 

worksurfaces.
1.   Position the worksurface onto leg and stretcher 

supports. Push the rear of the worksurface 

against the vertical edge of the stretcher. The top 

of the worksurface and the top of the stretcher 

should be level. Align the holes in the worksurface 

with the holes in the support surfaces. Hold the 

worksurface in place by hand until all screws are 

installed.

2.   From underneath the assembly, insert screws 

through the stretcher flange into the worksurface. 

Insert screws through the leg support flanges into 

of the worksurface. Tighten all screws.

3.   Align tie plates between each adjoining 

worksurface. Insert screws through the tie plate 

into the two adjoining worksurfaces and tighten.

  

Worksurface tie plates are required between all 

flanking worksurfaces.

Repeat these steps for all worksurfaces needed in 

this stage of the installation.

NOTICE

Note:

  Some worksurfaces, such as those with 

LCD Lifts, require additional assembly. For 

installation details, see the instruction sheet 

included with any specialty components.

Содержание Compass































































Отзывы:

Нет отзывов