manualshive.com logo in svg

Eaton Compass, Руководство по установке, Страница: 19 / 62

Поделиться
Скачать
Eaton Compass Скачать руководство пользователя страница 19

15

Compass

Installation Manual

COMPASS INSTALLATION MANUAL

         www.eaton.com/compass

Finish Trim Pieces

Compass components include wire way covers, top 

caps, and Eaton logos.

Wire Way Covers

Wire way covers attach to the open channel on the 

interior side of legs and uprights. Wire way covers 

have left and right versions. The flared side of the 

wire way cover aligns to the rear of the assembly. 

Wire way covers have cutouts that can be removed to 

accommodate cabling.
Legs of 26 inches in height use two wire way covers: 

191/2 inches on the bottom and 6 inches just below the 

worksurface.
Legs of 65 inches in height use four wire way covers: 

191/2 inches on the bottom, 6 inches just below the 

worksurface, 211/4 inches just above the worksurface, 

and 143/4 inches at the top.
Uprights of 36 inches use two wire way covers: 211/4 

inches just above the worksurface, and 143/4 inches at 

the top.
Uprights of 12, 16, and 20 inches use one wire way 

cover each, or 12, 16, and 20 inches respectively.

Top Caps

Top caps insert into the very top of legs and uprights. 

Top caps have left and right versions that match the 

shape of the wire way covers.

Eaton Logo

Eaton logos are provided separately to be attached 

during installation. Place logos on a few workspaces 

per installation. Logos can be placed on stretchers 

and inside overhead compartments. For more 

information about attaching logos, see the Installing 

Compass Components section.

Accessories

A wide variety of accessories can be integrated with 

your Compass components. For more information, 

refer to the installation instructions provided with 

these accessories.

Содержание Compass































































Отзывы:

Нет отзывов