manualshive.com logo in svg

Eaton Compass, Руководство по установке, Страница: 12 / 62

Поделиться
Скачать
Eaton Compass Скачать руководство пользователя страница 12

8

Compass

Installation Manual

COMPASS INSTALLATION MANUAL

         www.eaton.com/compass

Full Leg

A full leg attaches to the end of a stretcher and the 

bottom of a worksurface. Full legs are available in left 

and right versions. The panel part of a full leg is steel 

and matches the appearance of modesty panels.
Full legs are available in heights (H) of 29 and 

65 inches and modular depths (D) of 18, 24, 30, 

or 36 inches. Both 29 and 65 inch legs support 

worksurfaces at 29 inches.

•   

Legs of 29 inches in height support organizer 

uprights of 12, 16, 20, and 36 inches. Legs of 65 

inches in height can be considered a 29 inch leg 

with an integrated 36 inch upright.

•   

Full leg item numbers describe the modular 

depth, overall height, and orientation (R=right and 

L=left). For example, CLF3065R supports a 30 inch 

worksurface, is 65 inches in height, and attaches to 

the right side of a worksurface.

•   

CLF2429L is a full leg that supports a 24 inch 

worksurface, is 29 inches in height, and attaches to 

the left side of a worksurface.

Joined Transition Leg

H legs attach to the ends of a stretcher and the 

Joined transition legs attach between two stretchers 

and the bottom of two worksurfaces, and are only 

available in a center version. Joined transition legs use 

separate worksurface support and a smaller foot to 

maximize clearance under the worksurface.

•   

Joined transition legs are available in heights (H) of 

29 and 65 inches and modular depths (D) of 18, 24, 

30, or 36 inches. Both 29 and 65 inch legs support 

worksurfaces at 29 inches.

•   

Legs of 29 inches in height support organizer 

uprights of 12, 16, 20, and 36 inches. Legs of 65 

inches in height can be considered a 29 inch leg 

with two integrated 36 inch uprights.

•   

Joined transition leg item numbers describe the 

modular depth and overall height. For example, 

CLLT3065 support a 30 inch wide worksurfaces, 

is 65 inches in height, and attaches to adjoining 

worksurfaces.

•   

CLLT2429 is a joined transition leg that supports a 

24 inch worksurfaces, is 29 inches in height, and 

attaches to adjoining worksurfaces.

Содержание Compass































































Отзывы:

Нет отзывов