manualshive.com logo in svg

Eaton Compass, Руководство по установке, Страница: 4 / 62

Поделиться
Скачать
Eaton Compass Скачать руководство пользователя страница 4

iv

Compass

Installation Manual

COMPASS INSTALLATION MANUAL

         www.eaton.com/compass

 

About This Guide

This guide describes how to configure and install the 

Compass

®

 modular office furniture system.

Audience

Read this document if you are responsible for 

ordering, configuring, or installing Compass modular 

office furniture.

Document Organization

This document is divided into two major sections.

•   

Conceptual information appears in the modular 

design sections.

•   

Step-by-step instructions appear in the installing 

compass components section.

Document Conventions

This document uses the following conventions:

•   

Notes, important options, and referenced steps are 

bold.

•   

Links are underlined.

•   

Document names appear in 

italics

.

•   

Acronyms are defined the first time they occur. The 

original term appears first, followed by the acronym 

in parentheses. For example: electrostatic discharge 

(ESD).

Related Documents

See Compass Modular Office Furniture at  

Eaton.com/compass.
Also see Compass Sit-to-Stand Modular Office 

Furniture at Eaton.com/compass.

Technical Support

For Compass Technical Support:

•   

Call technical office support at 800-321-9954

•   

Email technical office support at to.support@

wrightline.com

•   

Contact your Eaton Representative

Precautions

Compass is a modular office furniture system. Do not 

use Compass components for any other purpose.
Do not connect components in configurations that are 

not described in this document.

Содержание Compass































































Отзывы:

Нет отзывов