manualshive.com logo in svg

Eaton Compass, Руководство по установке, Страница: 5 / 62

Поделиться
Скачать
Eaton Compass Скачать руководство пользователя страница 5

1

Compass

Installation Manual

COMPASS INSTALLATION MANUAL

         www.eaton.com/compass

COMPASS INSTALLATION MANUAL

         www.eaton.com/compass

Introduction

The Compass modular desking system is a 

freestanding, steel-based design that meets or 

exceeds industry requirements for strength and 

durability. The systems modular design permits 

unlimited workspace configurations, and is completely 

scalable, reconfigurable, and available in multiple 

finishes.
You can quickly design, order, and install a wide range 

of technical furniture from a stand-alone desk to a  

full-service workspace.

Features:

Modular design
Proven durability of steel
Multiple finishes
Built-in levelers
Fully backed and warranted by Eaton
For ordering information contact your Eaton 

representative, or call 1-800-225-7348.

Compass Components Overview

The following illustration shows the basic types of 

Compass components: worksurfaces, legs, organizer 

panels, and overhead storage.

For a complete list of Compass components, see the 

modular design section

Service Offerings

Eaton offers a wide range of service and support 

options:

•   

Installation and assembly

•   

Inside delivery, strip, place, and remove debris 

(IDSPR)

•   

Product moving and reconfiguration

•   

Removal and disposal of old furniture and 

equipment

Modular Design

Compass is comprised of basic components that 

can be seamlessly combined to create unlimited 

workspace options.
Compass components are divided into four 

component types:

•

  Worksurfaces

 

Linear Worksurface

 

 Linear Transition Worksurface Corner Worksurface

 

 Corner  Transition  Worksurface  Peninsula 

Worksurface

 

Jetty Worksurface

 

Conference End Worksurface Conference Table

•

  Legs and Uprights

 

Standard Leg H Leg

 

Full Leg

 

Joined Transition Leg

 

Non-Joined Transition Leg Corner Leg

 

Organizer Upright

•

  Panels

 

Organizer Panel Modesty Panel

•

  Overhead Storage

 

Overhead Compartment Shell Flipper Doors

 

Cabinet Doors

 

 Linear Storage Shelf Corner Storage Shelf 

Transaction Shelf

•

  Accessories

Overhead storage

Overhead 

storage

Leg

Worksurface

Содержание Compass































































Отзывы:

Нет отзывов