Docomo foma N905i, Руководство пользователя

Страница: 436 / 548

434
Appendix/
External
Device
s/Troubleshooting
“Check new messages is set all
OFF”
●
New messages cannot be checked because none of the items is
selected in “Set check new messages”.
Select items to check in “Set check new messages”. p.213
“Connection failed (403)”
●
Connection to the site failed for some reason. Retry connection.
ー
“Connection failed”
●
This is displayed when the host settings are incorrect. Set the host
correctly, using “Host selection” under Connection setting.
●
Connection to i-mode failed for some reason. Retry connection.
p.180
ー
“Connection failed”
●
Set “Caller ID Notification” to “ON” and retry. p.48
“Connection interrupted”
●
i-mode connection was interrupted due to poor reception. Move to
a location where the reception is good before using the i-mode
service.
●
If this message appears when the signal is strong and the “ ”
mark is displayed, the connected site is very busy. Retry later.
p.166
ー
“Continue using the i-
α
ppli and
communication?”
●
This is displayed when you selected “NO” or “Terminate i-
α
ppli” in
response to “The number of i-
α
ppli communications is large.
Continue communication?” Select “YES” to continue i-
α
ppli
communication. Select “Terminate i-
α
ppli” to stop using the
i-
α
ppli.
ー
“Could not read”
●
Copying could not be completed, for some reason. Replace with a
different microSD card and try to copy again.
ー
“Could not start because of a
different FOMA card (UIM)”
●
This is displayed when an i-
α
ppli that is restricted by FOMA card
operational restriction attempted to start automatically.
p.40
“Could not start the specified
software because of a different
FOMA card (UIM)”
●
This is displayed when you specify and attempt to start an i-
α
ppli
that is restricted by FOMA card operational restriction.
p.40
“Data is too long A part is
deleted”
●
The size of address, subject or text or more than one data
exceeds the maximum, and the Compose message screen
appears with the excess part deleted.
ー
“Data transmission is frequent
Press CLR and confirm data
transmission”
●
This is displayed when the number of communications from an
i-
α
ppli standby screen becomes very large within a certain
period. Press
t
to select whether or not to permit
communications from the i-
α
ppli standby display, or to close the
i-
α
ppli standby display.
p.238
“Dial/Receive calls activating
Original lock”
●
This is displayed when you have attempted a prohibited operation
while the original lock is applied to “Dial/sending mail” and to
“Incoming/Mail disp.”. p.133
“Download failed”
●
This is displayed when a download of a melody, Chara-den or
download dictionary suffered a communication error or improper
data.
ー
(During Infrared Data
Exchange/iC Exchange)
“No response Retry?”
●
The receiving terminal cannot be found/detected. If Ir
communication is used, make sure the Ir ports are facing each
other. If iC exchange is used, check the FeliCa marks and place
them together again. You can select “YES”, then press
d
to try
again.
p.307
p.309
“Editing now Cannot delete”
●
This is displayed if you attempt to delete a mail message saved in
the Save box while it is being edited.
ー
“Enter correct Network Security
Code”
●
This is displayed when an incorrect network security code was
input for a function which requires network security code entry.
Enter the correct network security code. p.124
“Error in image Does not work
correctly”
●
This is displayed when a Flash movie cannot be played due to an
error found in the data.
ー
Error Message Explanation and Solution Ref. page