Docomo foma N905i, Руководство пользователя

Страница: 182 / 548

180
i-
m
ode/i-motion/i-Channe
l
i-motion auto-replay (default: ON) → p.184
Auto-display setting (default: MessageR preferred)
…… Sets the automatic display of MessageR/F.
Start attachment (auto) (default: ON)
……
Sets
whether the attached/pasted melody automatically
plays when opening the MessageR/F.
Use phone information (default: Accept) → p.181
Message list display (default: 2 lines)
……
Sets the
number of lines in the message list screen.
Home URL …… Sets use of the home URL display
function. When set to “Valid”, pressing
a
( マナー )
on the standby screen displays the screen of the
stored URL. You can enter URLs of up to 256 single-
byte characters.
Invalid (default) …… Disables the home URL
display setting.
Valid …… Enables the home URL display
setting.
Select the Home URL field and enter a URL to
be stored.
Sound effect (default: ON) …… Sets whether to play
the sound effects for the Flash movies in a site page
or screen memo.
Set i-mode arrival act (default: PushTalk preferred)
…… Sets whether to answer an incoming PushTalk
call during i-mode communication.
Open tab setting (default: Open at the back side)
…… When a page opens in a new window, set
whether it replaces the current display (opens in
front) or leaves the original display in place (opens
back side).
mlt win. setting → p.174
Check settings …… Displays the settings set in
“i-mode settings”.
Reset
……
Resets the settings specified in “i-mode
settings” to the default settings.
Setting the connection timeout
<Set connection timeout>
This option sets time-out duration for which the
FOMA terminal automatically stops trying to connect
when a site is busy and there is no response.
1
i
X
“Settings”
X
“Connection
setting”
X
“Set connection timeout”
X
Select any item:
60 seconds (default) …… Automatically stops
connecting if there is no response for 60 seconds.
90 seconds
……
Automatically stops connecting if
there is no response for 90 seconds.
Unlimited …… Does not automatically stop
connecting.
Setting a host different from i-mode
host (ISP connection)
<Host selection>
You need to select a different host when you want to
use a service other than i-mode. If you change the
host to a host other than i-mode, you cannot use
i-mode or i-mode mail.
z
You can store up to 10 hosts other than “i-mode”.
1
i
X
“Settings”
X
“Connection
setting”
X
“Host selection”
X
Highlight
“<Not recorded>”
X
o
(Edit)
X
Enter
your security code
X
Select any item:
Host name …… Sets the host name. You can enter
up to 9 double-byte or 18 single-byte characters.
Host number …… Sets the host number. You can
enter up to 99 single-byte characters.
Host address …… Sets the host address. You can
enter up to 30 single-byte characters.
Host address2 …… Sets the host address2. You can
enter up to 30 single-byte characters.
2
o
(Finish)
N
<Sound effect>
z
Even if sound effects are set to “ON”, some Flash
movies may not make any sound.
<Set i-mode arrival act>
z
If “i-mode preferred” is selected, the received
PushTalk call is not recorded on the Received calls
record.
* There is normally no need to change this
setting.
N
z
Note that costs of packet communication while you are
connected to a host other than i-mode are not covered
by “Pake-Houdai” or “Pake-Houdai Full” deal.
z
When you change the host, the ticker of i-Channel is
turned off. The ticker is turned on again automatically
when the information is updated automatically or
when
u
is pressed to receive the latest information.