manualshive.com logo in svg

Dini Group DN9002K10PCI, Руководство пользователя

Поделиться
Скачать
Dini Group DN9002K10PCI Скачать руководство пользователя страница 67

H A R D W A R E  

Some of the current limitations of the main.txt interface are given here. Directories are not 
supported for FPGA configuration files. All bit files must be contained in the root directory of 
the card. File name lengths for bit files are limited to 8 characters. You can still use bit files with 
longer file names by specifying the DOS version of the file name in the main.txt file. For 
example, to configure FPGA A with the file 

Com_apple_sj45_ethn0_fpga_b_121107b.bit 

You can use the main.txt command 

FPGA A: com_ap~1.bit 

3.4.2

 

Hardware 

The Compact Flash interface is hot-swappable. 

An activity LED, DS147, located next to the Compact Flash slot indicates activity on this 
interface. 

Due to a flaw in the software design, some Compact Flash cards may be incompatible with the 
DN9002K10PCI. Please contact 

[email protected]

 if you find an incompatible card, so 

that we can add software support for it. 

Also, the board only accepts CompactFlash cards formatted in the FAT file system. Most newer 
compact flash cards come pre-formatted with the FAT32 file system. In this case, the 
DN9002K10PCI will not be able to recognize files on the card. 

3.5

 

Configuration Registers 

The configuration control on the DN9002K10PCI is controlled by setting “configuration 
registers”. Basically, these are just locations in the memory space of the on-board micro 
controller that controls the board’s function. A full description of the function of this micro 
controller is omitted, but some of the registers in this space are required to be accessed over 
USB or PCI to control the board. For information on how to access this address space over 
USB or PCI, see the corresponding section in this chapter. 

REGISTER ADDRESS 

 

FUNCTION 

FPGA_RESET 

DF22 

Write 0x2 to hold reset. 0x0 to release 

G0_N_VAL 

DF29 

Sets the divider value of G0 

G0_M_VAL 

DF30 

Sets the 8442 multiplier of G0 

G1_N_VAL 

DF31 

Sets the 8442 divider value of G1 

G0_M_VAL 

DF32 

Sets the 8442 multiplier of G1 

G2_N_VAL 

DF33 

Sets the 8442 divider value of G2 

G2_M_VAL 

DF34 

Sets the 8442 multiplier of G2 

UPDATE_CLOCK_FLAG DF40 

When high, each bit causes the configuration circuit to 
update the represented clock frequency with the 
current M and N values. 0x01 is G0, 0x02 is G1, 0x04 
is G2 

DN9002K10PCI User Guide 

www.dinigroup.com

 57 

 

Содержание DN9002K10PCI










































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды