See exploded view
00000000 (0)
Item number
Quantity
English
16
10
Maintenance (with the engine
stopped)
14
Repairs
We carry out all repairs in the
shortest possible time and at the
most economical prices (see
overleaf for our address).
S
A
V
15
Spare parts
For quick supply of spare parts and to
avoid any lost time it is essential to quote
the data on the manufacturer's plate fixed
to the machine and the part number of the
part to be replaced with every order.
In the event of deterioration and
scrapping of the machine, the
following items must be disposed
of in accordance with the
requirements of the legislation in
force.
16
Scrapping
• Main materials :
■
Motor : Aluminium (AL), Steel (AC),
Motor :
Copper (CU), Polyamide (PA)
■
Machine : Steel sheet (AC),
■
Machine :
Cast iron (FT)
■
Machine :
Aluminium (AL)
The instructions for use and spare parts found in
this document are for information only and are
not binding.
As part of our product quality improvement policy,
we reserve the right to make any and all technical
modifications without prior notice.
• After a certain amount of use, it may be
necessary to reasonably tighten the belts.
To do that:
■
Loosen the screw (M) of the seating
[SEE FIG. 3].
■
Swivel the base.
■
Tighten the screw (M) (tightening
torque 86xNm).
11
Motor belt tension
• Engine speed is preset at the factory for
proper sawing speed. It should be
periodically verified.
• To change governor setting, refer to
engine manual.
12
Governor settings
• Tighten all the nuts and bolts regularly.
• Check the tension of the belts. Tighten
them without overdoing it.
• When storing the machine, we
recommend removing the blade and
storing it carefully.
• Check that there is sufficient water supply
during operation, inspect the holes in the
fork regularly.
• Tighten the blade firmly.
• Make sure the contact faces of flanges,
blade and axle are clean.
13
Important recommendations
The manufacturer declines all
responsibility for loss or damage
resulting from misuse or any
modification, alteration or
powering that does not conform
to the manufacturer's original
specifications.
If the battery does not need any
servicing, the battery clips must
be maintened in good condition.
In the event of prolonged
immobilization, disconnect the
clips and recharge the battery to
keep it in functioning condition.
At the work station, the sound
pressure level may exceed 85 db
(A)
In this case individual protection
measures must be taken.
When working in a limited or
closed area, make sure that the
ventilation is adequate. The
exhaust gases contain carbon
monoxide (exposure to this toxic
gas
can
cause
loss
of
consciousness and can be fatal).
After each use CLEAN the machine.
• The spindle bearings must be greased
after 8 hours of use, with a grease gun by
pumping three to five times the grease
into the greaser of the bearings. Only use
a Super lithium 12 based grease in
compliance with the NLG1 GRADE 2
consistency.
• Every 40 hours grease :
■
Depth control adjustment screw.
• Cleaning and greasing the chain
(automatic version).
• Check ENGINE OIL daily. Read engine
owners manual for OIL and OIL FILTER
change intervals. Use :
■
SAE 10W30 motor oil with API class
MS, SD, SE or better for PETROL
engines.
■
API class CD or CE for Hatz diesel.
• To empty the motor, place a funnel at the
drain outlet (V) [SEE FIG. 3].
AIR FILTER
• Read engine owners manual for
maintenance intervals. For extremely
dusty conditions you may have to clean
the air filter element 2 to 3 times a day.
• Replace any damaged filters or gaskets.
Dispose of the old oil as laid
down by the regulations in force.
Store in a safe place out ot reach
of children.
Remove all adjustment tools and
wrenches
Store diamond tool in a safe
place so it cannot be bent or
damaged.
"Engine Maintenance" : refer to
the engine maintenance booklet.
Never go over maximum blade
capacity and cutting depths.
OIL
LUBRICATION
8
To stop
• Disengage the blade from the groove.
• Reduce the motor speed before stopping.
• Turn off the water.
Motor off.
Emergency stop
(engine) :
Operate the switch on the
machine's control panel.
Emergency stop (electric
motor):
Press the red knob (circuit
breaker)
Entrust repairs to authorised
dealer only
• Several causes may be responsible for
stopping the blade in the saw groove or
the machine :
■
Tension the belt.
■
Lack of fuel (petrol or diesel) or lack of
power (electric).
■
Too rapid an advance or descent, etc.
■
Starting contactor fuse (25A) blown
(HONDA 18 BHP).
Automatic advance
- Protection fuses burnt out.
- Power supply (30A)
- Converter (5A)
• In all cases, disengage the blade from
the groove and make a complete check of
the machine.
9
Incidents during sawing
Emergency stop
(diesel engine) :
Speed control set to minimum
speed
Emergency stop
(automatic advance):
Press the emergency stop button
(the machine will automatically
move
backwards
slightly).
Returning the controller to 0
position then to the on-position
will start up the advance again.
