Digital Equipment DECserver 90L+ Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 112

background image

5

Troubleshooting the DECserver 90L+

This chapter describes how to troubleshoot the DECserver 90L+. To troubleshoot
your unit:

1.

Verify that the unit is properly installed.

2.

Note the fault condition.

3.

Isolate the problem. Use Table 5–1 as a guide to determine the probable
cause and the suggested solution.

Table 5–1 DECserver 90L+ Troubleshooting

If...

Then...

Do this...

The power LED is not
‘‘on’’

The DECserver 90L+
is not receiving proper
voltage.

Check the AC power connection
and verify that the AC outlet
is working. Check the power
connection on the DECserver 90L+.
If the problem still exists, replace
the power supply.

The self-test LED is not
‘‘on’’

The unit did not pass
self-test.

Replace the unit.

The network LED is not
‘‘on’’

The unit’s network
connector is not properly
terminated.

Check network connection.
Check if the segment is properly
terminated.

Disconnect unit from network.
Connect T-connector with two
50 ohm terminators. If the
LED lights, then it is a network
problem. Otherwise, replace the
unit.

(continued on next page)

Troubleshooting the DECserver 90L+ 5–1

«
...
93
94
95
96
97
...
»

Содержание DECserver 90L+

















































































































Отзывы:

Нет отзывов

Похожие инструкции для DECserver 90L+

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 2

CX PRINT SERVER 550

Бренд: Xerox Страницы: 166

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 100

AlphaServer ES47

Бренд: HP Страницы: 76

AlphaServer GS80

Бренд: HP Страницы: 88

Бренд: HP Страницы: 39

16/18-Port Cable Management Kit

Бренд: HP Страницы: 14

Бренд: HP Страницы: 49

AlphaServer ES47

Бренд: HP Страницы: 152

AlphaStation DS20

Бренд: HP Страницы: 15

AlphaServer ES45

Бренд: HP Страницы: 38

AB500A - Integrated Lights-Out Advanced

Бренд: HP Страницы: 43

AlphaServer GS1280 Systems

Бренд: HP Страницы: 59

2533t - Compaq Mobile Thin Client

Бренд: HP Страницы: 116

Бренд: HP Страницы: 206

127695-B21 - Smart Array 431 RAID Controller

Бренд: HP Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды