DeLUX MOISTURE Link G2 DP, Руководство по эксплуатации

Страница: 270 / 322

25

MicroM will reset from the lockout state only. This is especially useful where, through the use of
remote reset daughter boards, all reset inputs can be connected together to a common reset pushbut-
ton or intelligent device (PLC). If the push button is depressed as described above it will only cause
the unit that is in lockout to reset and not effect any other units.
Smart Recycle
If the push button is depressed and released greater than 5 seconds but less than 7 seconds, all con-
nected MicroM units will recycle back to the beginning of purge. All units that are in lockout will
remain in lockout.
Address Mode
If the unit is in the Idle or Standby mode and the push button is depressed and released for greater
than 10 seconds, the unit address of the MicroM will be displayed on the LED’s in a binary format.
The range of the address is 0 to 31 and is used for Modbus or E500 communications. Because the
default address is 0 and since address 0 would mean no LED’s would be lit; the ALARM LED is
made to flash when the address is 0. The OP CTRL LED is the least significant bit while the FLAME
relay is the most significant bit. The ALARM LED is used to indicate if the address is greater than or
less than 16. If the ALARM LED is flashing, the address is less than 16 and conversely if the
ALARM LED is solid, the unit address is greater than 16. This only applies to the address. To incre-
ment the address on the control, depress and release the RESET push button and observe the LED
pattern. If the RESET switch is untouched for 30 seconds, the current address displayed will be
stored to memory and the MicroM will automatically exit the address mode.
REMOTE DISPLAY
The MicroM provides an interface to the optional ED510 display module. The ED510 connects to
the MicroM through the plug-in board using a ED580 cable. The ED580 cable is available in 2, 4, or
8 foot lengths. Part number 129-145 -1 (4 ft.), -2 (8 ft.), -3 (2 ft.) is available for remote mounting the
ED510 Display Module and to provide NEMA 4 protection. ¤
The ED510 Display Module is a backlit, 2 line by 16 character LCD display with keypad to provide
both current operation and historical information of the MicroM. The ED510 contains a keypad con-
sisting of three push keys, SCRL, RESET and MODE. Remote reset is available through the ED510
Keypad.
The ED510 displays current burner status, first out annunciation in the event of a lockout condition,
historical burner information, detailed lockout information of the last six (6) lockout conditions and
programmer configuration information. Through the display the ability to program the unit address
for communications, as well as resetting the stored information (cycles, hours, and lockouts) to zero
is provided.
Depending on the information being displayed, data is displayed on the ED510 screen in the follow-
ing locations:
LED
BINARY
VALUE 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
★
16
OP CNTRL 1 -
●
-
●
-
●
-
●
-
●
-
●
-
●
-
●
-
Air Flow 2 - -
● ●
- -
● ●
- -
● ●
- -
● ●
-
PTFI 4 - - - -
● ● ● ●
- - - -
● ● ● ●
-
FLAME 8 - - - - - - - -
● ● ● ● ● ● ● ●
-
ALARM
16
✸ ✸ ✸ ✸ ✸ ✸ ✸ ✸ ✸ ✸ ✸ ✸ ✸ ✸ ✸ ✸ ✸
★
note: addresses 17-31 would repeat above pattern but with alarm LED steady on