Dell PowerEdge M600 Скачать руководство пользователя страница 76

Страница: 76 / 236

About Your System

Unsupported CPU

stepping detected.

Processor is not supported
by the blade.

Check for a BIOS update
using the Dell Support
website at

support.dell.com

If the problem persists,
install a supported processor.
See "Processors" on
page 128.

Warning! A fatal

error has caused

system reset.

Please check the

event log for

details.

Unspecified error.

Check the system event log
for information about the
error.

Warning! Following

faulty DIMMs are

disabled: DIMM

DIMM

Faulty or improperly
seated memory modules.

See "Troubleshooting Blade
Memory" on page 191.

Warning! No

microcode update

loaded for

processor

Unsupported processor.

Update the BIOS firmware
using the Dell Support
website at

support.dell.com

Warning: The

current memory

configuration is

not validated.

Change it to the

recommended memory

configuration or

press any key to

continue.

There is no memory
configuration error, but
the memory configuration
is not recommended by
Dell.

See "System Memory" on
page 105.

Table 1-18.

Blade Messages

(continued)

Message

Causes

Corrective Actions

Содержание PowerEdge M600













































































































































































































































Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды

Dell PowerEdge M600, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды