Dell PowerEdge M600 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 236

background image

22

About Your System

Table 1-3.

Blade Control Panel Features

Feature

Icon

Description

Blade power
indicator

Off – Power is not available to the blade, the blade is
in standby mode, the blade is not turned on, or the
blade is installed incorrectly. For detailed information
on installing a blade, see "Installing a Blade" on
page 98.

Green increasing from low brightness to full
brightness – Blade power on request is pending.

Green on – The blade is turned on.

Blade status/
identification
indicator

Off – The blade power is off.

Blue – Normal operating state

Blue blinking – The blade is being remotely
identified via the CMC.

Amber blinking – Blade has either detected an
internal error, or the installed mezzanine card(s) does
not match the I/O modules installed in the M1000e
enclosure. Check the CMC for an I/O configuration
error message and correct the error.

Blade power
button

N/A

Turns blade power off and on.

• If you turn off the blade using the power button

and the blade is running an ACPI-compliant
operating system, the blade can perform an
orderly shutdown before the power is turned off.

• If the blade is not running an ACPI-compliant

operating system, power is turned off immediately
after the power button is pressed.

• Press and hold the button to turn off the blade

immediately.

The blade power button is enabled by default by the
System Setup program.(If the power button option is
disabled, you can only use the power button to turn
on the blade. The blade can then only be shut down
using system management software.)

USB connector

Connects external USB 2.0 devices to the blade.

«
...
20
21
22
23
24
...
»

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

Бренд: Parker Страницы: 344

DHI-NVR5224-24P-4KS2

Бренд: Dahua Страницы: 24

Бренд: Paradyne Страницы: 20

Compshere 3000 Series

Бренд: Paradyne Страницы: 2

F-ZTAT H8/3048 Series

Бренд: Renesas Страницы: 34

Armor 101 Series

Бренд: Lochinvar Страницы: 28

Armor 101 Series

Бренд: Lochinvar Страницы: 44

Бренд: FONESTAR Страницы: 8

Бренд: QuickLink Страницы: 8

Optane Persistent Memory 200 Series

Бренд: Supermicro Страницы: 54

IP-Logic ZIG-IPPRO-RX

Бренд: Zigen Страницы: 4

Бренд: Neousys Technology Страницы: 24

Бренд: DFRobot Страницы: 30

Бренд: YASKAWA Страницы: 87

Бренд: Patton electronics Страницы: 8

Бренд: Jabra Страницы: 2

Бренд: Vivotek Страницы: 185

Бренд: Ublox Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды