manualshive.com logo in svg

Dell PowerEdge M600, Руководство владельца оборудования

Dell PowerEdge M600 - сервер нового поколения. Этот мощный компьютер обеспечит высокую производительность и надежность. Скачайте бесплатное руководство пользователя "Hardware Owner'S Manual" с нашего сайта для детальной информации о продукте. (Download it from manualshive.com).

Поделиться
Скачать
background image

About Your System

23

Using USB Diskette or USB DVD/CD Drives

Each blade has USB ports on the front of the blade which allows you to 
connect a USB diskette drive, USB flash drive, USB DVD/CD drive, keyboard, 
or mouse. (PowerEdge M905 and M805 blades have three USB ports; 
PowerEdge M605 and M600 blades have two ports.) The USB drives can be 
used to configure the blade. 

 

NOTICE: 

The system supports only Dell-branded USB 2.0 drives. The drive must be 

horizontal and level to operate properly. Use the optional external drive storage tray 
to support the drive while in use.

 

NOTE: 

If the drive must be designated as the boot drive, connect the USB drive, 

restart the system, then enter the System Setup Program and set the drive as first in 
the boot sequence (see "Using the System Setup Program" on page 79). The USB 
device will be displayed in the boot order setup screen only if it is attached to the 
system before you run the System Setup program.

You can also select the boot device by pressing the <F11> key during system startup 
and selecting a boot device for the current boot sequence.

Hard-Drive Features

•

The PowerEdge M805 and M905 blades support one or two hot-pluggable 
2.5 inch SAS hard drives.

•

The PowerEdge M600 and M605 blades support one or two hot-pluggable 
2.5-inch SATA hard drives 

or

 one or two 2.5 inch SAS hard drives.

 

NOTE: 

SAS and SATA hard drives cannot be mixed within a blade.

 

NOTE: 

SATA hard drives are not hot pluggable with the SATA repeater 

daughter card.

Hot-plug drive operation is supported if an optional RAID controller card 
is installed in the blade.

On blades with a diskless configuration, no disk controller is included in the 
blade, but hard-drive blanks and the internal storage backplane must be 
present to maintain proper airflow.

See 

Figure 1-8

 and Table 1-4 for information on the hard-drive indicators. 

Different patterns are displayed as drive events occur in the system. 

 

NOTICE: 

The blade must have a hard drive or a hard-drive blank installed in each 

hard-drive bay. 

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

ZETR 25 Installation Manual preview
25
Бренд: ZETR Страницы: 2
Barco EX Safety Manual preview
EX
Бренд: Barco Страницы: 100
Xinje XS Series User Manual preview
XS Series
Бренд: Xinje Страницы: 57
Queclink GV600 Series Instruction Manual preview
GV600 Series
Бренд: Queclink Страницы: 9
Accusys ACS-76500 Owner'S Manual preview
ACS-76500
Бренд: Accusys Страницы: 34
Alesis QUADRAVERB Service Manual preview
QUADRAVERB
Бренд: Alesis Страницы: 46
Cateye Urban Wireless CC-VT240W Instruction Manual preview
Urban Wireless CC-VT240W
Бренд: Cateye Страницы: 15
Riverbed SteelCentral AppResponse 2180 Upgrade And Maintenance Manual preview
SteelCentral AppResponse 2180
Бренд: Riverbed Страницы: 82
ZALMAN CNPS7000C Series User Manual preview
CNPS7000C Series
Бренд: ZALMAN Страницы: 8
Eurotech Zypad WL15 Series Quick Start preview
Zypad WL15 Series
Бренд: Eurotech Страницы: 2
Quadram Quadboard Operation Manual preview
Quadboard
Бренд: Quadram Страницы: 21
Areca ARC-12x4 Series Quick Installation Manual preview
ARC-12x4 Series
Бренд: Areca Страницы: 2
PairGain HiGain Line Unit HLU-388 Quick Installation Manual preview
HiGain Line Unit HLU-388
Бренд: PairGain Страницы: 7
Serial Cables PCI4-AD-x16HI-BG4 User Manual preview
PCI4-AD-x16HI-BG4
Бренд: Serial Cables Страницы: 15
Abus TVAC21000 User Manual preview
TVAC21000
Бренд: Abus Страницы: 98
ZALMAN CNPS10X Flex User Manual preview
CNPS10X Flex
Бренд: ZALMAN Страницы: 12
Abov A34M418YLN User Manual preview
A34M418YLN
Бренд: Abov Страницы: 8
Adaptec 2025ZCR - SCSI RAID Storage Controller Datasheet preview
2025ZCR - SCSI RAID Storage Controller
Бренд: Adaptec Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды