Dell PowerEdge M600 Скачать руководство пользователя страница 25

Страница: 25 / 236

About Your System

Table 1-4.

Hard-Drive Indicator Patterns

Indicator

State

Description

Activity indicator

Off

Drive is not being
accessed

Drive is being accessed

Status indicator
(SAS drives with
optional RAID
controller only)

Off

• Drive is ready for

removal.

• Drive bay is empty.
• Power is off to the

blade.

Green

Drive is online.

Green, blinking slowly

Drive is rebuilding.

Green, blinking quickly

Drive is being identified.

Amber

Drive has failed or has an
error. See
"Troubleshooting Hard
Drives" on page 192.

Amber blinking slowly,
Green blinking slowly, then off

The drive has reported a
predictive failure event,
and should be replaced.

Содержание PowerEdge M600













































































































































































































































Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды

Dell PowerEdge M600, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды