Dell PowerEdge M600 Скачать руководство пользователя страница 192 | Manualshive

Страница: 192 / 236

background image

192

Troubleshooting Your System

2

Enter the System Setup program and check the system memory setting.
See "Using the System Setup Program" on page 79.

If the amount of memory installed matches the system memory setting, go
to step 8.

3

Remove the blade. See "Removing a Blade" on page 96.

4

Open the blade. See "Opening the Blade" on page 100.

CAUTION:

The memory modules are hot to the touch for some time after the blade

has been powered down. Allow time for the memory modules to cool before
handling them. Handle the memory modules by the card edges and avoid touching
the components.

5

Reseat the memory modules in their sockets. See "Installing Memory
Modules" on page 120.

6

Close the blade. See "Closing the Blade" on page 104.

7

Install the blade. See "Installing a Blade" on page 98.

8

Run the system memory test in the system diagnostics. See "Running
System Diagnostics" on page 197.

If the test fails, see "Getting Help" on page 217.

Troubleshooting Hard Drives

Problem

•

Device driver error

•

Improperly seated hard drive carrier

•

Faulty hard drive or hard-drive carrier

•

Device drivers

Action

CAUTION:

Many repairs may only be done by a certified service technician. You

should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.

«
...
190
191
192
193
194
...
»

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

Бренд: F5 Страницы: 2

Бренд: F5 Страницы: 90

Бренд: F5 Страницы: 47

Бренд: X-Micro Страницы: 9

Бренд: X-Micro Страницы: 19

Бренд: Paradyne Страницы: 112

Бренд: FOR-A Страницы: 39

Supero SAS-826A

Бренд: Supero Страницы: 16

Бренд: Lutron Electronics Страницы: 4

Бренд: AXIOMTEK Страницы: 58

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

CY62136EV30 MoBL

Бренд: Cypress Semiconductor Страницы: 12

Бренд: ADTRAN Страницы: 20

Бренд: XtendLan Страницы: 21

Бренд: Ariesys Страницы: 10

Бренд: Kaya Instruments Страницы: 48

Serial Attached SCSI (SAS) Expander Card

Бренд: Adaptec Страницы: 26

Бренд: UMAX Technologies Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды