Dell PowerEdge M600 Скачать руководство пользователя страница 104

Страница: 104 / 236

104

Installing Blade Components

Figure 3-6.

Inside a Full-Height Blade (PowerEdge M805 Shown)

Closing the Blade

CAUTION:

Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. Before you begin this
procedure, review the safety instructions that came with the system.

Ensure that no tools or parts are left inside the blade.

Align the notches in the edges of the enclosure with the cover alignment
pins on the inner sides of the cover.

optional mezzanine card 1 -
Fabric C

optional mezzanine card 2 -
Fabric B

optional mezzanine card 3 -
Fabric C

optional mezzanine card 4 -
Fabric B

SD card location

processor CPU2 and heat sink

hard drive 1

hard drive 0

hard-drive backplane

processor CPU1 and heat sink

video riser card

Содержание PowerEdge M600













































































































































































































































Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды

Dell PowerEdge M600, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды