Dell PowerEdge M600 Скачать руководство пользователя страница 74

Страница: 74 / 236

About Your System

Read fault.

Faulty diskette, diskette
drive, or optical drive.

Replace the diskette. Ensure
that the drive cable is
properly connected. See
"Troubleshooting USB
Devices" on page 183 or
"Troubleshooting Hard
Drives" on page 192 for the
appropriate drive(s)
installed in your system.

Remote

Configuration

update attempt

failed.

Blade could not
implement Remote
Configuration request.

Retry Remote
Configuration.

Sector not found.

Seek error.

Seek operation

failed.

Faulty diskette or hard
drive.

Replace the diskette. If the
problem persists, see
"Troubleshooting Hard
Drives" on page 192 for the
appropriate drive installed in
your system.

Shutdown failure.

Shutdown test failure.

Ensure that all memory
modules are properly
installed. See
"Troubleshooting Blade
Memory" on page 191. If the
problem persists, see
"Getting Help" on page 217.

Spare bank

enabled.

Memory sparing enabled.

Information only.

The amount of

system memory has

changed.

Faulty memory module.

See "Troubleshooting Blade
Memory" on page 191. If the
problem persists, see
"Getting Help" on page 217.

Information only, if you
have changed the memory
configuration.

Table 1-18.

Blade Messages

(continued)

Message

Causes

Corrective Actions

Содержание PowerEdge M600













































































































































































































































Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды

Dell PowerEdge M600, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды