manualshive.com logo in svg

Dell PowerEdge M600, Руководство владельца оборудования

Dell PowerEdge M600 - сервер нового поколения. Этот мощный компьютер обеспечит высокую производительность и надежность. Скачайте бесплатное руководство пользователя "Hardware Owner'S Manual" с нашего сайта для детальной информации о продукте. (Download it from manualshive.com).

Поделиться
Скачать
background image

40

About Your System

–

The CMC supports setting an optional enclosure Maximum Power 
Limit, which will either alert or take actions, such as throttling server 
modules and/or preventing the power up of new blades to keep the 
enclosure under the defined maximum power limit.

–

The CMC monitors and automatically controls cooling fans based on 
actual ambient and internal temperature measurements.

–

The CMC provides comprehensive enclosure inventory and 
status/error reporting.

•

The CMC provides a mechanism for centralized configuration of the 
following:

–

The M1000e enclosure’s network and security settings

–

Power redundancy and power ceiling settings

–

I/O switches and iDRAC network settings

–

First boot device on the server blades

–

The CMC checks I/O fabric consistency between the I/O modules and 
blades and disables components if necessary to protect the system 
hardware.

–

User access security.

The CMC has two Ethernet ports: Gb1 is used to connect to the external 
management network. The connector labeled STK ("stack") will allow CMCs 
in adjacent enclosures to be daisy-chained. A 24-port Ethernet switch 
provides internal communication between the iDRAC on each blade, I/O 
modules, optional KVM, and optional second, redundant CMC.

 

NOTE: 

The 24-port Ethernet switch is reserved for internal communication 

between the iDRAC on the blades to the CMC and the external management 
network. If two CMCs are installed, the heartbeat for CMC redundancy is also 
present and CMC redundancy is supported over this internal network. This internal 
network is outside the data path from host LOMs and the mezzanine cards in the 
blades.

At least one CMC must be installed in the primary CMC bay (see 
Figure 1-14) for the system to power up. If a second, optional CMC module is 
installed, failover protection and hot-plug replacement is available.

See the latest 

Dell Chassis Management Controller User's Guide

 at 

support.dell.com

 for complete instructions on how to set up and operate the 

CMC module. 

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

TC Electronic M300 Service Manual preview
M300
Бренд: TC Electronic Страницы: 2
Phytec L-843e.A1 Hardware Manual preview
L-843e.A1
Бренд: Phytec Страницы: 53
ZyXEL Communications EOC350 Series Quick Start Manual preview
EOC350 Series
Бренд: ZyXEL Communications Страницы: 2
Dahua NVS0X04DH Quick Start Manual preview
NVS0X04DH
Бренд: Dahua Страницы: 24
NEC P401-TMX4D User Manual preview
P401-TMX4D
Бренд: NEC Страницы: 2
Neo Instruments Mini Vent User Manual preview
Mini Vent
Бренд: Neo Instruments Страницы: 2
OpenVox B800P User Manual preview
B800P
Бренд: OpenVox Страницы: 13
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Бренд: Lanner electronics Страницы: 59
Atmel STK501 Specification Sheet preview
STK501
Бренд: Atmel Страницы: 2
Z-Wave IOMOD10F Hardware User Manual preview
IOMOD10F
Бренд: Z-Wave Страницы: 42
Cypress Semiconductor CY8C24223A Specification Sheet preview
CY8C24223A
Бренд: Cypress Semiconductor Страницы: 31
CyberResearch CPBF PMX-233 User Manual preview
CPBF PMX-233
Бренд: CyberResearch Страницы: 59
Qlogic QMI2472 Datasheet preview
QMI2472
Бренд: Qlogic Страницы: 2
Digisol DG-SR2004 User Manual preview
DG-SR2004
Бренд: Digisol Страницы: 73
Promise Technology Pegasus R4 Product Manual preview
Pegasus R4
Бренд: Promise Technology Страницы: 148
SonicWALL Internet Security Appliances Administrator'S Manual preview
Internet Security Appliances
Бренд: SonicWALL Страницы: 293
Commax CVN-0430F User Manual preview
CVN-0430F
Бренд: Commax Страницы: 122
IBA ibaPADU-S-IT-16 Manual preview
ibaPADU-S-IT-16
Бренд: IBA Страницы: 80

Бренды по названию

Популярные бренды

Загрузить еще бренды