manualshive.com logo in svg

Dell PowerEdge M600, Руководство владельца оборудования

Dell PowerEdge M600 - сервер нового поколения. Этот мощный компьютер обеспечит высокую производительность и надежность. Скачайте бесплатное руководство пользователя "Hardware Owner'S Manual" с нашего сайта для детальной информации о продукте. (Download it from manualshive.com).

Поделиться
Скачать
background image

158

Installing Enclosure Components

Power Supply Modules 

The M1000e enclosure supports up to six hot-pluggable power supply 
modules, accessible from the enclosure back panel. 

 

NOTE: 

The 2360-W power supply modules require 200–240 V input from a PDU. If 

the power supply modules are plugged into 110-V electrical outlets, the system will 
not power up. 

 

NOTE: 

In addition to supplying power to the system, the power supply modules also 

have internal fans that provide thermal cooling for the blades. A power supply 
module must be replaced if an internal fan failure occurs. 

System Power Guidelines

Your system has one of the following power supply configurations:

•

Three 2360-W power supply modules, which do not provide redundancy if 
one power supply module fails. The power supplies are installed in bays 1 
though 3.

•

Six 2360-W power supply modules, which provide redundancy if up to 
three power supply modules fail.

The CMC module controls power management for the system. You can 
program the CMC to configure the power budget, redundancy, and dynamic 
power of the entire enclosure (chassis, servers, I/O modules, iKVM, CMC, 
and power supplies). The power management service optimizes power 
consumption and re-allocates power to different modules based on real-time 
demand. For more information, see "Power Management" in the 

Dell Chassis 

Management Controller User’s Guide.

 

NOTE: 

The wattage of a power supply module is listed on its regulatory label. 

 

NOTICE: 

PDU inlet cords for this system may be too thick to fit in the wire guides 

installed in the rack vertical rails. If this is the case, remove the wire guides by 
removing the attachment screw securing each guide. Route the PDU inlet cords 
along the vertical rails, securing them with tie wraps or Velcro strips. 

Power Supply Blanks

If the M1000e enclosure is operated with only three power supplies, power 
supply blanks must be installed in the three unoccupied power supply bays 
(4 through 6) to maintain proper cooling airflow in the enclosure. 

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

3Com IntelliJack NJ200 Datasheet preview
IntelliJack NJ200
Бренд: 3Com Страницы: 4
Campbell NL115 Instruction Manual preview
NL115
Бренд: Campbell Страницы: 42
Farallon NetLINE USB User Manual preview
NetLINE USB
Бренд: Farallon Страницы: 26
Observint N16 Quick Setup Manual preview
N16
Бренд: Observint Страницы: 11
Tripp Lite N48M Series Installation Manual preview
N48M Series
Бренд: Tripp Lite Страницы: 20
Analog Devices Linear SCP-LT8362-S-EVALZ Demo Manual preview
Linear SCP-LT8362-S-EVALZ
Бренд: Analog Devices Страницы: 8
Baldor Modbus Plus Installation And Operating Manual preview
Modbus Plus
Бренд: Baldor Страницы: 34
Renesas Compact Emulator M30620T-CPE User Manual preview
Compact Emulator M30620T-CPE
Бренд: Renesas Страницы: 52
Lancom 7100 VPN Manual preview
7100 VPN
Бренд: Lancom Страницы: 70
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Бренд: ADC Страницы: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Бренд: Renesas Страницы: 28
Advantech ARK-1380 User Manual preview
ARK-1380
Бренд: Advantech Страницы: 50
B&B Electronics 4 Channel Input Buffer Board SDAIBB Product Manual preview
4 Channel Input Buffer Board SDAIBB
Бренд: B&B Electronics Страницы: 22
Bose PowerMatch ESPLink Quick Start Manual preview
PowerMatch ESPLink
Бренд: Bose Страницы: 2
Ubiquiti EdgeSwtch 5XP Quick Start Manual preview
EdgeSwtch 5XP
Бренд: Ubiquiti Страницы: 13
TP-Link VIGI NVR1004H-4P Quick Installation Manual preview
VIGI NVR1004H-4P
Бренд: TP-Link Страницы: 2
Kontron ePanel-C3 Technical Manual preview
ePanel-C3
Бренд: Kontron Страницы: 62
Noraxon TeleMyo 2400T V2 User Manual preview
TeleMyo 2400T V2
Бренд: Noraxon Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды