Dell PowerEdge M600 Скачать руководство пользователя страница 166

Страница: 166 / 236

166

Installing Enclosure Components

iKVM Module

Removing an iKVM Module

Disconnect the cables attached to the iKVM module.

Press in the release latch on the handle and rotate the handle away from
the module front panel. See Figure 4-4.

Slide the module out of the enclosure.

Installing an iKVM Module

Ensure that the module handle is fully open. See Figure 4-4.

Slide the module into the enclosure until the handle contacts the
enclosure.

To fully seat the module, close the handle until the release latch snaps into
place.

If applicable, connect the keyboard, monitor, and mouse to the module.

I/O Modules

NOTICE:

If you remove an I/O module, you must either replace it with another I/O

module or with a filler blank to maintain cooling airflow through the system
enclosure.

Removing an I/O Module

If you have not already installed the cable enumerators to make removal
and replacement of the I/O modules easier and faster, install them now.
See the

Rack Installation Guide

for details.

Disconnect the cables attached to the I/O module.

Lift the latch on the end of the module’s handle and rotate the handle
away from the module. See Figure 4-6.

Slide the I/O module out of the enclosure.

Install the I/O connector cover.

Содержание PowerEdge M600













































































































































































































































Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды

Dell PowerEdge M600, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды