Dell PowerEdge M600 Скачать руководство пользователя страница 187 | Manualshive

Страница: 187 / 236

background image

Troubleshooting Your System

187

Action

NOTICE:

The fan modules are hot-pluggable. Remove and replace only one fan

module at a time in a system that is turned on. Operating the system without all six
fan modules for extended periods of time can cause the system to overheat.

1

Locate the faulty fan.

Each fan module has indicators that identify a faulty fan. See Figure 1-12.

2

Remove the fan module. See "Removing a Fan Module" on page 161.

3

Examine the blades for debris. If debris is present, carefully remove it.

4

Reseat the faulty fan. See "Installing a Fan Module" on page 162.

5

If none of the fans show a fault LED and the blades will not power on,
check the LCD display or CMC for status messages.

6

If the problem is not resolved, install a new fan.

7

If the new fan does not operate, see "Getting Help" on page 217.

Troubleshooting the CMC Module

Problem

•

CMC module is not operating properly

•

System message indicates a problem with the CMC module

•

CMC module does not failover or fail back

•

CMC module cable connections

Action

NOTE:

To eliminate the possibility of a hardware problem with the module or its

attaching devices, first ensure that the module is properly initialized and
configured. See the

Configuration Guide

and the documentation that came with the

module before performing the following procedure.

1

Verify that the latest firmware is installed on the CMC module.

See

support.dell.com

for the latest firmware and refer to the release notes

for firmware compatibility and update information.

2

Verify that the CMC(s) have valid IP addresses for the subnet. Verify using
the ICMP

ping

command.

«
...
185
186
187
188
189
...
»

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

Бренд: 3xLogic Страницы: 2

Бренд: EVS Страницы: 30

Бренд: SIIG Страницы: 6

Бренд: Telit Wireless Solutions Страницы: 113

Бренд: SIIG Страницы: 20

EZ-Extender Analog 120-Pin Probing Board

Бренд: Analog Devices Страницы: 29

Seven Solutions WR-ZEN Series

Бренд: Orolia Страницы: 167

Бренд: AOpen Страницы: 18

DataPlot CB1224

Бренд: B-G Instruments Страницы: 4

Бренд: IBM Страницы: 130

Бренд: ASROCK Страницы: 173

Бренд: Rosewill Страницы: 2

LinkStation 500

Бренд: Buffalo Страницы: 139

Бренд: Telit Wireless Solutions Страницы: 79

Бренд: A.E.B. Страницы: 10

Бренд: Lenze Страницы: 15

Бренд: Wharfedale Pro Страницы: 19

Бренд: E-line Страницы: 231

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды