Dell PowerEdge M600 Скачать руководство пользователя страница 191 | Manualshive

Страница: 191 / 236

background image

Troubleshooting Your System

191

8

Ensure that the appropriate operating system drivers are installed and that
the protocol settings are configured to ensure proper communication.

Troubleshooting Blade Components

The following procedures describe how to troubleshoot the following
components. See Figure 3-4 for the location of the components inside the
blade.

•

Memory

•

Hard drives

•

Microprocessors

•

Blade system board

•

Battery

Troubleshooting Blade Memory

Problem

•

Faulty memory module

•

Faulty blade board

Action

CAUTION:

Many repairs may only be done by a certified service technician. You

should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.

NOTE:

Before performing the following procedure, ensure that you have installed

the memory modules according to the memory installation guidelines for the blade.
See "System Memory" on page 105.

1

Restart the blade.

a

Press the power button once to turn off the blade.

b

Press the power button again to apply power to the blade.

If no error messages appear, go to step 8.

«
...
189
190
191
192
193
...
»

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

SATA II ExpressCard 34

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

Бренд: FOR-A Страницы: 39

RADEON 9800 PRO

Бренд: ATI Technologies Страницы: 20

Aquaduct 240 eco

Бренд: Aqua Computer Страницы: 20

Бренд: Ubiquiti Страницы: 13

VIGI NVR1004H-4P

Бренд: TP-Link Страницы: 2

Бренд: Kontron Страницы: 62

Бренд: Altera Страницы: 33

Бренд: ADS Technologies Страницы: 21

AirStation G54 WLA2-G54

Бренд: Buffalo Страницы: 8

ELITE LCD UPGRADE KIT

Бренд: Corsair Страницы: 11

Cyclades CS4008

Бренд: Avocent Страницы: 2

Бренд: Xilinx Страницы: 43

ACC-BKT-AX-BEAM

Бренд: Extreme Networks Страницы: 35

Cascade Express

Бренд: Riverbed Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды