Dell PowerEdge M600 Скачать руководство пользователя страница 128

Страница: 128 / 236

128

Installing Blade Components

Figure 3-15.

Installing a NIC Hardware Key

Processors

NOTE:

The following removal and installation procedures apply to the PowerEdge

M905, M805, M605, and M600 blades. Appropriate illustrations are provided for
each type of processor.

Processor Installation Guidelines

PowerEdge 905 Systems

•

The PowerEdge 905 supports dual-core or quad-core AMD™ Opteron™
8

xxxx

Series processors only.

•

Four processors must be installed; dual-processor configurations are not
supported

•

Only AMD 8

xxxx

MP series processors are supported.

NIC hardware key

connector on system board

Содержание PowerEdge M600













































































































































































































































Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды

Dell PowerEdge M600, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды