DELAIR UX11 Скачать руководство пользователя страница 88

Страница: 88 / 94

User Manual UX11

10.2

Replacing a wing

Every 100 flights, the wings have to be replaced as a preventive maintenance action. The wing should

also be replaced if it shows excessive damage such as (but not limited to): bent or broken wing

tip, damaged push rod, teared elevon horn, noisy servo actuator, broken or deformed plastic part,

damaged elevons (hinge, trailing edge), bent connector pins.
Orderable parts:

Part Number

This part comprises

FDG-000055

1 × UX11 right wing

FDG-000056

1 × UX11 left wing

FDG-000033

1 × UX11 right wing
1 × UX11 left wing

Required tools:

• None

Required parts:

• Left wing and/or right wing

Step:

• Replace the part by the new one.

10.3

Replacing the belly plate

Every 100 flights, the belly plate has to be replaced as a preventive maintenance action. The belly plate

should also be replaced if it shows excessive damage such as (but not limited to): torn-off foam beds,

loose fitting with the fuselage.
Orderable parts:

Part Number

This part comprises

FDG-000057

1 x UX11 belly plate

Required tools:

• None

Required parts:

• 1 × Belly plate

Step:

• Replace the part by the new one.

Delair

676, Rue Max Planck – 31670 Toulouse-Labège, France

Tel: +33 (0) 5 82 95 44 06

| www.delair.aero

Capital: 238 110,30 € - APE: 3030Z – Intra-Community VAT number: FR90 53 09 69 781 – 530 969 781 R.C.S. Toulouse

This document is the sole property of Delair and cannot be used or reproduced without the written authorization of Delair.

Содержание UX11































































































Результаты поиска

Содержание UX11

Отзывы:

DELAIR UX11, Руководство пользователя, Страница: 88 / 94

Результаты поиска

Содержание UX11

Отзывы: