DELAIR UX11 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 94

DELAIR UX11 Скачать руководство пользователя страница 46

User Manual UX11

6.2 Check the site

Note

When checking the site you should refer to the relevant AIP (Aeronautical Information Publication) and

NOTAM (Notice to Airmen) documents for your region.

• Identify the airspace and geographic environment of the site.
• Check the relevant aviation charts and make sure the flight area is not near any of the following

areas:

– Forbidden airspace
– Airports and airfields (except with prior permission)
– Power plants (except with prior permission)

• Take special care around the following areas:

– Parachute jumping and parasailing areas
– Winch areas
– High-pressure gas-releasing units (documented in AIPs or NOTAMs)
– Congested areas (for example, towns)

• Check if other aerial or ground activities are planned at or near the site, for example major

public events.

Note

This list is not exhaustive. It is the responsibility of the user to be aware of any local conflicts that may result

in a hazardous situation.

Delair

|

676, Rue Max Planck – 31670 Toulouse-Labège, France

|

Tel: +33 (0) 5 82 95 44 06

| www.delair.aero

Capital: 238 110,30 € - APE: 3030Z – Intra-Community VAT number: FR90 53 09 69 781 – 530 969 781 R.C.S. Toulouse

This document is the sole property of Delair and cannot be used or reproduced without the written authorization of Delair.

37

«
...
44
45
46
47
48
...
»

Содержание UX11































































































Отзывы:

Нет отзывов