DELAIR UX11 Скачать руководство пользователя страница 15

Страница: 15 / 94

User Manual UX11

LED

Status

Description

Slow blinking green

Ready for binding sequence

Fast blinking green

Waiting for user to confirm binding by pressing

Confirm

button

BIND

Solid green

Binding OK

Blinking green

Checklist in progress

Solid red

Error detected during checklist

CHECKLIST

Solid green

All checks have been completed

Blinking green

Waiting for user to confirm takeoff by pressing

Confirm

button

TAKEOFF

Solid green

The aircraft is ready for takeoff

Note

When performing maintenance operations on the aircraft, all LEDs blink green.

2.2 Tablet

2.2.1

Requirements

• Operating system: Android 6 ("Marshmallow") to Android 9 ("Pie")
• Screen:

– 8 inches or higher
– Screen designed for outdoor use (under direct sunlight), with appropriate brightness

and anti-glare protection

• Storage: 8 GB or higher
• Internal memory: 1.5 GB or higher (2 GB is recommended)
• GPS sensor: Recommended since

Delair Flight Deck

application uses the Tablet GPS location

(when available) for non-mandatory features.

• Networking/communications:

– 3G-capable
– Wi-Fi 802.11 a/b/n or ac, supporting both the 2.4 GHz and 5 GHz Wi-Fi bands

Note

Support for the 5 GHz Wi-Fi band is mandatory for use with the

Delair Link

module.

Delair

676, Rue Max Planck – 31670 Toulouse-Labège, France

Tel: +33 (0) 5 82 95 44 06

| www.delair.aero

Capital: 238 110,30 € - APE: 3030Z – Intra-Community VAT number: FR90 53 09 69 781 – 530 969 781 R.C.S. Toulouse

This document is the sole property of Delair and cannot be used or reproduced without the written authorization of Delair.

Содержание UX11































































































Результаты поиска

Содержание UX11

Отзывы:

DELAIR UX11, Руководство пользователя, Страница: 15 / 94

Результаты поиска

Содержание UX11

Отзывы: